Siemens SINAMICS G120C - Page 62

Commissioning
4.2 Commissioning with BOP-2 operator panel
SINAMICS G120C, FSD ... FSF inverters
62 Compact Operating Instructions, 11/2016, FW V4.7 SP6, A5E39339884B AA
No.
Description
p0845 BI: No coast down/coast down (OFF2) signal
source 2
p0848
BI: No quick stop/quick stop (OFF3) signal source
1
p0849
BI: No quick stop/quick stop (OFF3) signal source
1
p0852
BI: Enable operation
p0854
BI: Master control by PLC
p0855
BI: Unconditionally release holding brake
p0856
BI: Enable speed controller
p0857
Power Module monitoring time [ms]
p0858
BI: Unconditionally close holding brake
p0860
BI: Line contactor, feedback signal
p0861
Line contactor, monitoring time [ms]
r0863
CO/BO: Drive coupling status word / control word
.00 1 = closed-loop
control, operation
.01 1 = operate line
contactor
p0867 Power unit main contactor hold time after OFF1
[ms]
p0869
Configuration sequence control
.00
1 = keep main contactor closed for STO
r0898 CO/BO: Control word sequence control
r0899
CO/BO: Status word sequence control
p0922
PROFIdrive telegram selection
1
Standard telegram 1, PZD-2/2
20
Standard telegram 20, PZD-2/6
352
SIEMENS telegram 352, PZD-6/6
353 SIEMENS telegram 353, PZD-2/2, PKW-
4/4
354 SIEMENS telegram 354, PZD-6/6, PKW-
4/4
999
Free telegram configuration with BICO
r0944
CO: Counter for fault buffer changes
r0945
Fault code
r0946
Fault code list
r0947
Fault number
r0948
Fault time received in milliseconds [ms]
r0949
Fault value
p0952
Fault cases, counter
r0964
Device identification
No.
Description
p0965
PROFIdrive profile number
p0969 System runtime relative [ms]
p0970
Reset drive parameters
0 Inactive 1 Reset parameters
except for Safety
5 Reset safety pa-
rameters
10 Load setting 10
11
Load setting 11
12
Load setting 12
100
Reset BICO interconnections
p0971
Save parameters
0
Inactive
1 Save in nonvolatile storage (RAM → ROM)
10
Save in a non-volatile memory as setting 10
11
Save in a non-volatile memory as setting 11
12
Save in a non-volatile memory as setting 12
p0972
Drive unit reset
p1000
Speed setpoint selection
p1001 CO: Fixed speed setpoint 1 [rpm]
p1002
CO: Fixed speed setpoint 2 [rpm]
…
…
p1015
CO: Fixed speed setpoint 15 [rpm]
p1016
Fixed speed setpoint mode
1 Direct selection 2 Selection, binary
coded
p1020
BI: Fixed speed setpoint selection bit 0
p1021
BI: Fixed speed setpoint selection bit 1
p1022
BI: Fixed speed setpoint selection bit 2
p1023
BI: Fixed speed setpoint selection bit 3
r1024 CO: Fixed speed setpoint effective [100 % ≙
p2000]
r1025
BO: Fixed speed setpoint status
.00
Fixed speed setpoint selected
p1030
Motorized potentiometer configuration
00
Storage active
01 Automatic operation, ramp-function genera-
tor active
02
Initial rounding active
03 Storage in NVRAM active
p1035
BI: Motorized potentiometer setpoint raise