Siemens SINAMICS G120C - Page 72

Commissioning
4.2 Commissioning with BOP-2 operator panel
SINAMICS G120C, FSD ... FSF inverters
72 Compact Operating Instructions, 11/2016, FW V4.7 SP6, A5E39339884B AA
No.
Description
r5600
Pe hibernation ID
p5602 Pe hibernation pause time, minimum [s]
p5606
Pe hibernation duration, maximum [ms]
p5611 Pe energy-saving properties, general
.00 Inhibit
PROFIenergy
.01 Drive triggers OFF1
.02 Transition to hibernation from PROFIdrive
state 4 possible
p5612
Pe energy-saving properties, mode-dependent
r5613
CO/BO: Pe energy-saving active/inactive
p5614
BI: Set Pe Switching On Inhibited signal source
r7758
Know-how protection Control Unit serial number
r7759 Know-
how protection Control Unit reference serial
number
p7760
Write protection/know-how protection status
.00
1 = Write protection active
.01
1 = Know-how protection active
.02 1 = Know-how protection temporarily un-
locked
.03 1 = Know-how protection cannot be deac-
tivated
.04 1 = Memory card copy protection active
.05
1 = basis copy protection active
.06 1 = trace and measuring functions for diag-
nostic purposes active
p7761
Write protection
0
Not active
1
Active
p7762 Write access for control using multi-master third-
party bus system
0
Free write access independent of p7761
1
No free write access (p7761 is active)
p7763 Know-how protection OEM exception list number
of parameters
p7764
Know-how protection OEM exception list
p7765 Know-how protection memory card copy protec-
tion
.00 1 = extended copy protection - linked to
memory card and CU
.01 1 = basic copy protection active - linked to
memory card
.02 1 = trace and measuring functions permitted
for diagnostic purposes
p7766
Know-how protection password input
p7767
Know-how protection password new
p7768
Know-how protection password confirmation
No.
Description
p7769 Know-how protection memory card setpoint serial
number
p7775 NVRAM data action
r7843
Memory card serial number
r8540 BO: STW1 from BOP/IOP in manual mode
r8541 CO: Speed setpoint from BOP/IOP in manual
mode
p8542
BI: Active STW1 in BOP/IOP manual mode
p8543 CI: Active speed setpoint in BOP/IOP manual
mode
p8552
IOP speed unit
p8558
BI: Selection IOP manual mode
r8570 Macro Drive object
Display of the macro files stored in the inverter.
See also p0015.
p8805
Identification and Maintenance 4 configuration
0:
Standard value for I&M 4 (p8809)
1:
User value for I&M 4 (p8809)
p8806
Identification and Maintenance 1
[0…31]
Plant ID (PID)
[32…53]
Location ID (LID)
p8807
Identification and Maintenance 2
[0…15]
YYY-MM-DD hh.mm
p8808
Identification and Maintenance 3
[0…53] Arbitrary supplementary information
and remarks (ASCII)
p8809
Identification and Maintenance 4 (signature)
r8859
PROFINET identification data
r8909
PN Device ID
p8920
PN Name of station
p8921
PN IP Address of Station
p8922
PN Default Gateway of Station
p8923
PN Subnet Mask of Station
p8924
PN DHCP mode
p8925
PN interfaces configuration
0:
No function
1:
Activate the configuration
2:
Activate the configuration and save
3:
Delete configuration