What causes measuring error in Siemens SITRANS F C MASSFLO MASS 6000 Measuring Instruments?
A measuring error in Siemens Measuring Instruments can be caused by several factors. It could be due to a faulty zero-point, in which case you should make a new zero-point adjustment. If you see error codes P40, F61, F62, or F63, you should replace the SENSORPROM unit. If you see error code F70, you should replace the MASS 6000.
What to do if my Siemens SITRANS F C MASSFLO MASS 6000 Measuring Instruments show no flow signal?
If your Siemens Measuring Instruments are showing no flow signal, there could be several reasons. First, ensure that the current and digital outputs are activated. Also, check the flow direction and change it if it's reversed. If an error code W31 is displayed, make sure that the measuring pipe is full. For an error code F60, the MASS 6000 may need to be replaced. If the cause is undefined, check the cables and connections, and if the problem persists, replace the MASS 6000. If you see error code P41, switch off the MASS 6000, wait 5 seconds, and then switch it back on.
Why does my Siemens Measuring Instruments indicate flow when there is no flow in the pipe?
If your Siemens Measuring Instruments indicate flow even when there is no flow, it could be due to a couple of reasons. First, the measuring pipe might be empty, so ensure that the measuring pipe is full of liquid and select the empty pipe limit. Another potential cause is that the electrode cable is insufficiently screened. Ensure that the electrode cable is properly connected and sufficiently screened.
How to fix unstable flow signal on Siemens SITRANS F C MASSFLO MASS 6000?
An unstable flow signal in Siemens Measuring Instruments can stem from several factors: pulsating flow, air bubbles in the medium, vibrations, or pump noise. To address this: 1. Increase the time constant. 2. Ensure the medium does not contain air bubbles. 3. Make sure that the sensor is mounted on a rigid frame without vibrations. 4. Ensure that the pump frequency is different from the resonance frequency of the sensor.
Why Siemens SITRANS F C MASSFLO MASS 6000 display is empty?
An empty display on your Siemens Measuring Instruments can be due to two primary reasons: a problem with the supply voltage or a defective MASS 6000. To resolve this, first check the supply voltage. If the supply voltage is correct, the MASS 6000 may be defective and require replacement.
What to do if I lost totalizer data on my Siemens SITRANS F C MASSFLO MASS 6000 Measuring Instruments?
If you've experienced a loss of totalizer data on your Siemens Measuring Instruments, it might be due to an initializing error. In this case, you should reset the totalizer manually.
General| Measurement Principle | Coriolis |
|---|---|
| Accuracy (Mass flow) | ±0.1% of rate |
| Repeatability | ±0.05% of rate |
| Process Temperature | -50°C to +200°C |
| Ambient Temperature | -40°C to +60°C |
| Output Signal | 4-20 mA, HART, PROFIBUS PA, PROFIBUS DP, Foundation Fieldbus |
| Power Supply | 24 V DC |
| Housing Material | Aluminum or stainless steel |
| Protection Class | IP67 |
Guidelines for installing the MASS 2100 sensor, including mounting orientation and vibration.
Details on ATEX survey and requirements for instruments in potentially explosive atmospheres.
Overview of intrinsically safe data and cable specifications for safe operation.
Wiring diagrams for IP 20 and IP 65 enclosures, including intrinsically safe terminals.
Detailed wiring guide connecting the MASS 6000 signal converter to the MASS 2100 sensor.
Details on the operator and setup menu structure.
Guide for setting current, digital pulse, and frequency outputs.
Procedures for resetting totalizers, batch counters, and performing zero point adjustments.
Comprehensive list of error codes, their meaning, and suggested remedies for the MASS 6000.
Guidance on diagnosing and resolving common symptoms like empty display or no flow signal.
To Next Page