MAG 8000 & MAG 8000 CT
27
SFIDK.PS.026.D9.02
4. Commissioning
FT/PDM Meter Display Parameter/data type Factory settings Data range
number version view Fix parameter or meter data that not are changeable
717 All - Log period 22 totalized (2)
718 All - Log period 22 fault status See 168
719 All - Log period 22 status information See 169
720 All L23 Date of log period 23
721 All L23 Log period 23 totalized (1)
722 All - Log period 23 totalized (2)
723 All - Log period 23 fault status See 168
724 All - Log period 23 status information See 169
725 All L24 Date of log period 24
726 All L24 Log period 24 totalized (1)
727 All - Log period 24 totalized (2)
728 All - Log period 24 fault status See 168
729 All - Log period 24 status information See 169
730 All L25 Date of log period 25
731 All L25 Log period 25 totalized (1)
732 All - Log period 25 totalized (2)
733 All - Log period 25 fault status See 168
734 All - Log period 25 status information See 169
735 All L26 Date of log period 26
736 All L26 Log period 26 totalized (1)
737 All - Log period 26 totalized (2)
738 All - Log period 26 fault status See 168
739 All - Log period 26 status information See 169
800 Advanced - Insulation test enable No Yes / No
801 Advanced - Insulation test interval 30 0 to 65535
802 Advanced - Insulation value
803 Advanced - Insulation test date 2000-01-01 T00:00 year-month- day T
hours:minutes:seconds
804 Advanced - Insulation tests fulfilled 0
810 Advanced - Leakage detection mode Off Off/ fix value/ fix + lowest value
811 Advanced - Leakage source Flow rate Flow rate / volume
812 Advanced - Start period for leakage 120min=2:00 [24:00] 0 to 1430
detection minutes (0-23:50)
813 Advanced - Duration leakage detection 120min=2hours 1 to 144 (1440 minutes)
814 Advanced - Leakage value unit Flow / volume unit
815 Advanced - Leakage limit 1 0 to 1*10^9
816 Advanced - Leakage excitation frequency 1.5625 Hz 1/15Hz, 1/5Hz, 1.5625Hz,
3.125Hz, 6.25Hz, 1/30Hz, 1/60Hz
817 Advanced - Leakage status Leakage status; 1: Finished
successfully, 2: Leakage detection
running, 3: Leakage detection failed
(SystemStatus have fatal error), 4:
Leakage detection failed (Empty-pipe
detection disabled), 5: Leakage detection
failed (Coil current off), 6: Leakage
detection failed (Insulation test was
active during detection), 7: Leakage
detection stopped because leakage
parameter was changed.
818 Advanced - Periods with possible leakage
819 Advanced - Leakage periods before alarm 3 0 to 255
820 Advanced - Reset leakage period information No Yes / No
821 Advanced St1 Latest leakage period flowrate 0
822 Advanced St1 Latest leakage period volume 0
823 Advanced - Lowest measured leakage value 1000000000
824 Advanced - Date of lowest leakage value 2000-01-01 T00:00 year-month-day T
hours:minutes:seconds
825 Advanced - Highest measured leakage value 0
826 Advanced - Date of highest leakage value 2000-01-01 T00:00 year-month-day T
hours:minutes:seconds
830 Advanced R8 Next settling date PS3 production date and time year-month-day T
hours:minutes:seconds
831 Advanced R9 Latest settling date PS3 production date and time year-month-day T
hours:minutes:seconds
832 Advanced R9 Latest totalizer 1 value 0
To Next Page
Loading...
