To Next PageTo Next PageWhat to do if Siemens SITRANS F M MAGFLO have measuring error?
If your Siemens Measuring Instruments are showing a measuring error, first check the installation to ensure it is correct. The issue may be related to the SENSORPROM® unit. Depending on the specific error code (P40, P44, F61, F62, or F63), you may need to install or replace the SENSORPROM® unit. If the error code is F71, the MAG 5000/6000 may need replacement.
What to do if Siemens SITRANS F M MAGFLO Measuring Instruments show no flow signal?
If your Siemens Measuring Instruments are showing no flow signal, there could be several reasons. First, ensure that the current or digital output is enabled. Check the cables and connections. If the flow direction is reversed, change it. Also, make sure that the measuring pipe is full. In some cases, the MAG 5000/6000 unit might be defective and require replacement. As a last resort, switch off MAG 5000/6000, wait 5 seconds, and switch it on again.
How to fix Siemens Measuring Instruments with an empty display?
If the display of your Siemens MAG 5000/6000 Measuring Instruments is empty, it could be due to a couple of reasons. First, check the power supply and inspect the connector for bended pins. If the power supply is not the issue, the MAG 5000/6000 unit itself might be defective and need to be replaced.
Why Siemens SITRANS F M MAGFLO Measuring Instruments indicates flow with no flow in pipe?
If your Siemens Measuring Instruments indicate flow even when there is no flow in the pipe, it might be due to a few reasons. The measuring pipe could be empty, so ensure that the measuring pipe is full. If empty pipe cut-off is OFF, select empty pipe cut-off. Also, check the electrode connection and ensure that the electrode cable is connected and sufficiently screened.
What causes unstable flow signal in Siemens Measuring Instruments?
An unstable flow signal in Siemens Measuring Instruments can be caused by several factors. These include: 1. Pulsating flow, which can be addressed by increasing the time constant. 2. Low conductivity of the medium, which may require a special electrode cable. 3. Electrical noise potential between the medium and sensor, necessitating sufficient potential equalization. 4. Air bubbles in the medium; ensure the medium is free of air bubbles. 5. High concentration of particles or fibers; increase the time constant.
Why Siemens SITRANS F M MAGFLO display 'Maximum'?
If your Siemens Measuring Instruments display 'Maximum', it could be due to W30 or W21 issues. For W30, check Qmax in the Basic Settings. For W21, change the volume/pulse or change the pulse width.
What causes Siemens SITRANS F M MAGFLO Measuring Instruments measuring approx. 50%?
If Siemens Measuring Instruments are measuring approximately 50%, it is likely due to a missing electrode connection. Check the cables to ensure all electrode connections are properly connected.
How to fix loss of totalizer data in Siemens SITRANS F M MAGFLO Measuring Instruments?
If you experience a loss of totalizer data in your Siemens Measuring Instruments, it might be due to W20. To resolve this, reset the totalizer manually.
What to do if Siemens SITRANS F M MAGFLO shows signs in display?
If your Siemens Measuring Instruments are showing signs in the display, it's likely due to a totalizer roll over. You can resolve this by resetting the totalizer or increasing the totalizer unit.
General| Brand | Siemens |
|---|---|
| Model | SITRANS F M MAGFLO |
| Category | Measuring Instruments |
| Language | English |
Guidance on sensor placement and orientation for optimal measurement.
Overview of Ex survey and related approval standards.
Technical data for intrinsically safe operation and overview of Ex parameters.
Specific intrinsically safe data for MAG 6000 I transmitter.
Detailed Ex approval information for different sensor models.
Specific electrical connection details for MAG 6000 I transmitter.
Configuration of fundamental flowmeter parameters and units.
Configuration of current, digital, and pulse outputs.
Configuration of digital and relay output functions.
Accessing and using the service mode for diagnostics.
Display and management of flow rate, totalizers, and batch functions.
Table of error codes, their text, and remedy.
Common issues and their solutions for MAG transmitters.
Diagnostic steps for checking the MAG sensor's condition.
