Siemens ZIC-4A - Releasing Service Wiring

Siemens Industry, Inc.
Building Technologies Division
P/N 315-033050-1514
Figure 9
ZIC-4A Releasing Service Wiring
NOTES
1. All wiring must be in accordance with
Article 760 of NEC or local building
codes.
2. Electrical Ratings: 24VDC
2mA max @ Supervisory
3A max @ Alarm
3. All circuits are power limited to
NFPA 72 per NEC 760.
4. EOL resistor, 24k ohms,
1 watt, 5%, P/N 140-820405.
5. Polarity shown in active state for UL
compliant wiring only.
6. N/A
7. Releasing is wired for Class B only.
8. Any circuit may be used.
9. Input voltage sources can be daisy-
chained.
10. For Compatible Solenoids, refer to
table at right.
11. Refer to Zeus Quick Start Guide (P/N
315-033875) for information about
programming of releasing service.
12. Refer to CAB1/CAB1R (P/N 315-
0330007) and CAB2-BB/CAB3-BB (P/
N 315-033009) Installation
Instructions for details on
the separation of power
limited and non-power
limited wiring.
13. Positive or negative ground
fault detected at <40K ohms
for terminals 1-16.
14. For FM approved Pre-Action/
Deluge: All initiating devices
connected to the system
must be wired CLASS A.
15. Wiring diagram shown for
24VDC solenoid.
16. Wiring diagram shown for
12VDC solenoids (2 units in
series.)
17. Wiring diagram shown for
6VDC solenoids (4 units in
series.)
18. The ZIC-4A circuit must be
configured as “NAC Steady”.
The “Releasing Zone” usage
in Zeus is only to be used
for legacy UL releasing
applications that did not
include the REL-EOL.
19. The ZIC-4A circuit must
include a UL864 listed
Releasing Disconnect
Switch such as Siemens
Model RSM-5, P/N S54339-
F1-A1. The switch position
must be monitored using an
input module such as the
HTRI-M using the second
set of contacts.
RELEASING ZONE
ZONE 3
RELEASING ZONE
ZONE 1
RELEASING ZONE
ZONE 2
REL-EOL
MODULE
+
-
+
-
+
-
+
-
* The REL-EOL ships
with three resistors.
Use the 24K resistor
(P/N 140-034677)
with the ZIC-4A.
See Note 15 See Note 14 See Note 14 See Note 16
1 2 3 4 5 6 7 8
9 10 11 12 13 14 15 16
+
+
+
-
+
-
+
-
17 18 19 20 21 22 23 24
ZONE 1 & 2
INP
U
T
ZONE 3
INP
U
T
ZONE 4
INP
U
T
ONE SLOT OF CC-5
REL-EOL
MODULE
REL-EOL
MODULE
REL-EOL
MODULE
RELEASING ZONE
ZONE 4
+
-
+
-
+
-
+
-
+ +
-
-
--
NC
NC
NC
NC
NC
NC
NC
NC
24K,
1/2W
5%
*
24K,
1/2W
5%
*
24K,
1/2W
5%
*
24K,
1/2W
5%
*
Disconnect
Switch
Supervising
Module
Disconnect Circuit
Disconnect
Circuit
Disconnect
Circuit
Disconnect
Circuit
SDIONELOSELBITAPMOC
NOITACILPPARERUTCAFUNAM
ROLEDOMDIONELOS
REBMUNTRAP
SNEMEIS
REBMUNTRAP
FOREBMUN
SDIONELOS
SEIRESNI
MUMIXAM
FOREB
MUN
SDIONELOS
DRACREP
LAVORPPA
31APFN
)eguleDnoitcA-erP(
OCSA
701A0128R
A/N
CDV42enO4LU
701A0128TCDV42enO4LU
RENNIKS
2C111C0N00N99NBG1237CDV42enO4LU
52XBL2VLCDV42enO4LU
1002APFN
OCSA6-235812VHGB119796-005CDV6ruoF61LU
ETITPANS
5F4A-BN2-A3282GB219796-005CDV21owT8LU
6F4
A-BN2-A3282GB319296-005CDV42enO4LU
4F4A-BN2-A3282GB119796-005CDV6ruoF61LU
B495239GB176946-005CDV42enO4LU
XLT
42-2-CEY
PC/8210AP
GB529796-005CDV42enO4LU
42-2-CEYPC/7330AP
GNIKIV
19511
A/N
CDV42enO4LU
29511CDV42enO4LU
59511CDV42enO4LU
10611CD
V42enO4LU
20611CDV42enO4LU
51231CDV42enO4LU
34831CDV42enO4LU
44831CDV42enO4LU
EDDIK000-494798-KWA/NCDV42enO4LU
SUNAJ18481,22702A
/NCDV42enO4LU
XAMINIM323988A/NCDV42enO4LU
Initiating devices configured for supervisory signaling
are latching by default. If non-latching behavior is
required, check the self restoring supervisory checkbox
in the node properties for your Zeus configuration.