EasyManua.ls Logo

Silvercrest SL 80/2 100CI - User Manual

Silvercrest SL 80/2 100CI
104 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
Important
additional information to the owner manual of the
digital satellite receiver SilverCrest SL 80/2 100CI
This additional information is an important component of your owner manual.
Please keep this additional information carefully within your owner manual.
Point 1
After finishing the basic installation, the integrated hard disk drive (HDD) has to be
formatted, in order to adjust it to the receiver. This procedure needs to be done only one
time at the initial operation. Please proceed as follows:
Press button MENU (8) on the remote control. The main menu appears.
Move the blue bar with the arrow buttons up (12) res. down (13) to the main
menu point “HDD / USB applications”.
Press the button OK (14).
Move the blue bar with the arrow buttons up (12) res. down (13) to the menu point
„HDD Manager“.
Press the button OK (14).
Move the blue bar in the menu “HDD Manager” with the arrow buttons up (12) res.
down (13) to the menu point „Format HDD“.
Press the button OK (14).
Insert with the numeric buttons the current password (factory default 0000).
Confirm the appearing message with the button OK (14). The format procedure
starts.
The format procedure ist successfully finished, as soon as the sub-menu „HDD
Manager“ appears.
Press the button EXIT (9) on the remote control to leave the menu.
Point 2
External USB-Storage devices of the Mass Storage Device-class have to be in format
FAT 32.

Table of Contents

Questions and Answers

  • L
    larryfoxAug 12, 2025
    What to do if my Silvercrest SL 80/2 100CI system crashes?
    • C
      Curtis WilliamsAug 12, 2025
      If your Silvercrest Receiver system crashes and can no longer be operated, disconnect it from the power supply and then reconnect it after 10 seconds.
  • S
    stevenhammondAug 16, 2025
    Why does my Silvercrest SL 80/2 100CI Receiver show channel location but no image on TV?
    • R
      robert44Aug 16, 2025
      If the frontal display of your Silvercrest Receiver shows the channel location, but the TV set does not display any image, check the connection of the SCART cable and ensure that the TV is switched to the correct AV input mode.
  • R
    Robert RobinsonAug 20, 2025
    How to fix poor image quality on Silvercrest SL 80/2 100CI Receiver?
    • B
      brianhernandezAug 20, 2025
      If you are experiencing a poor image, blocking errors, small blocks, or sound stops on your Silvercrest Receiver, try to align the antenna more precisely, using the SIG key on the remote control. If the issue persists, the LNB might be defective and require replacement.
  • A
    Amanda WebbAug 25, 2025
    Why is my Silvercrest SL 80/2 100CI Receiver remote control not working?
    • M
      Melissa Boyd DDSAug 25, 2025
      If your Silvercrest Receiver remote control isn't working, first, replace the batteries. If that doesn't solve the problem, make sure you're aiming the remote control directly at the front of the receiver without any obstructions in the way.
  • M
    matthewhowardAug 28, 2025
    What to do if my Silvercrest Receiver has no sound or image but menus are displayed?
    • A
      Anita BeckerAug 28, 2025
      If there is no sound or image but the receiver menus are displayed on your Silvercrest Receiver, make sure the antenna is correctly pointed towards the satellite. Also, check the cable connections from the LNB to the receiver and from the receiver to the connected equipment. You may also need to align the antenna.
  • R
    Richard MartinezAug 31, 2025
    How to fix Silvercrest SL 80/2 100CI Receiver when satellite cannot be found?
    • J
      jreedAug 31, 2025
      If your Silvercrest Receiver cannot find a satellite or has no signal, turn it a few millimeters to the left, wait approximately 3 seconds, and repeat this process until both the signal and quality are displayed.
  • M
    Melvin GrantSep 4, 2025
    Why is the frontal display dark on my Silvercrest Receiver?
    • C
      clarkedestinySep 4, 2025
      To resolve a dark frontal display on your Silvercrest Receiver, ensure the mains cable is properly connected to both the power source and the receiver.
  • G
    Gregg KnightSep 8, 2025
    What to do if Silvercrest SL 80/2 100CI channel no longer transmitted?
    • A
      Alicia BarnesSep 8, 2025
      If a channel on your Silvercrest Receiver has received a new frequency and is no longer transmitted with the current data, delete the channel and start an automatic scan.

Silvercrest SL 80/2 100CI Specifications

General IconGeneral
BrandSilvercrest
ModelSL 80/2 100CI
CategoryReceiver
LanguageEnglish

Related product manuals