Simoniz S2000 - User Manual

Other manuals for Simoniz S2000

Owner's Manual10 pages

Questions and Answers

J
Jacob BestSep 10, 2025
Why does the output pressure of my Simoniz S2000 Pressure Washer vary high and low?
- S
  Stephanie CampbellSep 10, 2025
  If the output pressure of your Simoniz Pressure Washer varies high and low, fully turn on the water supply and inspect the garden hose for any kinks, leaks, or blockages. Also, check that the hoses and fittings are airtight and purge the pump by turning the machine off and squeezing the trigger gun until water flows steadily through the nozzle. Another potential cause is a clogged water inlet filter, which can be resolved by removing and rinsing it with warm water.
I
Ivan BarnettSep 12, 2025
What causes the output pressure of my Simoniz Pressure Washer to vary high and low (continued)?
- S
  Scott BrownSep 12, 2025
  If the output pressure of your Simoniz Pressure Washer continues to vary high and low, blow out the discharge nozzle or remove debris with a fine needle. If the gun, hose, or power nozzle are calcified, run distilled vinegar through the detergent tank.
S
Sara BrownSep 13, 2025
Why is the pump on my Simoniz Pressure Washer noisy?
- J
  Jennifer SandovalSep 13, 2025
  If your Simoniz Pressure Washer pump is noisy, check that the hoses and fittings are airtight and purge the pump by turning off the machine and squeezing the trigger gun until a steady flow of water emerges through the nozzle. Also, remove the water filter and rinse it in warm water, because the water filter may be clogged.
T
Tracey HansenSep 15, 2025
Why is my Simoniz S2000 Pressure Washer leaking water at the pump?
- K
  Kevin BurnsSep 15, 2025
  If you notice water leaking at the pump of your Simoniz Pressure Washer, check and replace any worn or broken o-rings. Ensure all connections are tightened securely. If the pump head or tubes are damaged from freezing, please call our toll free hotline: 1-866-293-WASH (1-866-293-9274).
M
Monique GallagherSep 18, 2025
Why does the pump pulsate on my Simoniz Pressure Washer?
- K
  Krystal BanksSep 18, 2025
  If the pump of your Simoniz Pressure Washer is pulsating, it could be due to worn or broken o-rings. Check and replace them as needed. Also, ensure that all connections are tightened. For piston packings worn, please call our toll free hotline: 1-866-293-WASH (1-866-293-9274).
A
April NewtonNov 23, 2025
How to fix Simoniz Pressure Washer when the engine will not start?
- T
  Tiffany FergusonNov 23, 2025
  If your Simoniz Pressure Washer engine isn't starting, there are several potential causes. First, make sure you have enough fuel. If pressure has built up, squeeze the gun trigger to relieve it. Ensure the engine is primed by pushing the primer button three times and that the spark plug wire is securely attached. A clogged air filter can also prevent starting, so clean and reassemble it. Check that the spray wand is in high pressure. The water supply must be at least 5 GPM at 20 PSI. Repair any leaks at the high-pressure hose fitting, applying sealant tape if needed. Clear any obstruction in the nozzle, and remove and clean the water filter screen. Remove air from the hose by disconnecting the water supply, turning it on to flush out air, and reconnecting. Ensure the throttle control lever...