How to fix a Simoniz S1750 Pressure Washer motor that won't start?
If your Simoniz Pressure Washer motor won't start, it could be due to a tripped circuit breaker or blown fuse, a loose plug, or a tripped pressure washer circuit breaker. Try these steps: Disconnect other devices on the same circuit and reset the breaker or replace the fuse. Reconnect the plug securely. Let the unit cool down completely before restarting.
Why Simoniz Pressure Washer motor will not start?
If your Simoniz Pressure Washer motor isn't starting, several factors could be at play. First, ensure the On/Off switch is in the “ON” ( | ) position. Check that the power cord is securely plugged in. If you're using an extension cord, it might be too long, of the wrong gauge, or damaged; try replacing it with a 25’ (7.6 m) or 50’ (15 m) 14/3 gauge cord. The electrical outlet itself may not be providing enough power, so test a different outlet. Finally, the pressure washer's circuit breaker may have tripped; allow the unit to cool down before restarting.
What causes pressure to increase when the gun is closed on a Simoniz S1750 Pressure Washer?
If the pressure increases when the gun is closed on your Simoniz Pressure Washer, it indicates that the bypass valve is not operating properly. Call Simoniz Customer Service Department.
What to do if Simoniz Pressure Washer has no detergent?
If your Simoniz Pressure Washer isn't dispensing detergent, start by checking if the detergent container is empty and add more if needed. Ensure the detergent bottle or suction tube is correctly connected. If the detergent is too thick, dilute it. Also, inspect the filter on the detergent suction tube for clogs and rinse with warm water to remove any debris. A damaged or clogged detergent suction tube can also be the culprit, so remove any obstruction or replace the tube if necessary. Make sure the nozzle is in the low-pressure position. Finally, check the discharge nozzle for obstructions and clear them with a fine needle if needed.
How to fix Simoniz Pressure Washer garden hose connection leaks?
If your Simoniz Pressure Washer's garden hose connection is leaking, first check for loose fittings and tighten them. If the leak persists, inspect the rubber washer; if it's missing or worn, insert a new one.
Why is my Simoniz S1750 motor running, but the pressure is low?
If your Simoniz Pressure Washer's motor is running, but the pump isn't building maximum pressure, several factors could be the cause: * The faucet might be closed. * The unit might have been stored in freezing temperatures. * The water inlet screen could be clogged. * There might be air in the pump. * The adjustable pressure knob may not be set to the maximum position. Here's what you can do: Open the faucet fully. Ensure the unit, including the hose, gun, and wand, is completely thawed. Clean the water inlet screen. Let the pressure washer run with the gun open and the wand removed until a steady stream of water is released. Make sure the adjustable pressure knob is set to the maximum position.
What to do if my Simoniz S1750 keeps tripping the circuit breaker?
If your Simoniz Pressure Washer keeps tripping the circuit breaker, it's likely due to a circuit overload, an extension cord that's too long or with too small wire size, or a partially blocked nozzle. Ensure the circuit is rated 15A or greater and disconnect other loads on the circuit. Use the correct extension cord as recommended in the Operator's Manual. Clean the nozzles.
Why is my Simoniz S1750 leaking water or oil from the bottom?
A small amount of leakage from the bottom of the pump of your Simoniz Pressure Washer is normal. If there is excessive leaking, call Simoniz Customer Service Department.
What to do if Simoniz S1750 unit does not reach high pressure?
If your Simoniz Pressure Washer isn't reaching high pressure, start by checking the diameter of your garden hose; replace it with a 1” (25 mm) or 5/8” (16 mm) hose if it's too small. Ensure that the water supply isn't restricted by checking the garden hose for kinks, leaks, or blockages. Make sure there's enough inlet water supply by fully opening the water source. Also, inspect the water inlet filter for clogs and rinse it in warm water if necessary. Verify that the power nozzle is in the high-pressure position. Lastly, the pump might be sucking air; check that all hoses and fittings are airtight, then turn off the machine and purge the pump by squeezing the trigger gun until a steady flow of water emerges through the nozzle.
What to do if Simoniz S1750 pump is noisy?
If your Simoniz Pressure Washer pump is making excessive noise, it might be sucking in air. Check that all hoses and fittings are airtight. Turn off the machine and purge the pump by squeezing the trigger gun until a steady flow of water emerges through the nozzle.
Covers motor defects for two years from original purchase.
Warrants accessories for three months from purchase date.
General safety precautions for operating the pressure washer.
Specific warnings about chemical use, injection hazards, and component ratings.
Warning about the main power switch.
Danger of electric shock due to improper grounding.
Details on adjustable wand, high-pressure/low-pressure settings.
Steps for safely turning off and cleaning the pressure washer.
Steps for winterizing using antifreeze for protection.
General| Maximum Pressure | 1750 PSI |
|---|---|
| Flow Rate | 1.4 GPM |
| Water Flow | 1.4 GPM |
| Hose Length | 20 ft |
| Engine | N/A (Electric) |
| Nozzles Included | Turbo, 15°, Soap |
To Next Page
