Tone controls:
Low: ±10
dB
at 60 Hz (XPLOD)
Mid: ±I0
dB
at I kHz (XPLOD)
High: ± I0
dB
at
10kHz
(XPLOD)
Power
requirements:
12
V DC boat battery
(negative ground (earth»
Dimensions: Approx.
178
x 50 x
182
mm
(71
18
x 2 x 7
1
14
in) (wlh/d)
Mounting
dimensions: Approx.
182
x
53
x
162
mm
(7 1/
4
x 2
1
/
8
x 6
1/2
in) (wlh/d)
Mass: Approx.
1.3
kg
(2
Ib
14
oz)
Supplied accessory:
Card remote commander:
RM
-XlSI
Parts for installation and connections (I set)
Optional accessories/equipment*:
Marine remote commander: RM-X60M,
RM-XIIM
Rotary commander: RM-X4S
BUS cable (supplied with an RCA pin cord):
RC-61
(1
m), RC-62 (2
m)
CD changer (10 discs): CDX-757MX
CD changer
(6
discs): CDX-T69
Source selector: XA-C40
AUX-IN selector: XA-300
USB connection cable for iPod: RC-l
OOIP
HD
Radio™
tuner: XT-100HD
* Accessories/equipment other than the marine
remote commander RM-X60M1X11
M are not
waterproof. Do not subject them to water.
Your
dealer
may
not
handle
some
of
the above listed
accessories.
Please
ask the
dealer
for detailed
information.
Design
and
specifications are subject to change
without notice.
• Halogenated flame retardants are not used in the
certain printed wiring boards.
• Halogenated flame retardants are not used in
cabinets.
• Packaging cushions are made from paper.
Troubleshooting
The
following checklist will help you remedy
problems you may encounter with your unit.
Before going through the checklist below, check the
connection and operating procedures.
If
the problem is not solved, visit the following
support site.
Support
site
For
customers
in
the
U.S.A.
and
Canada:
http://esupport.sony.com
http://www.xplodsony.com/
For
customers
in
Europe:
http://support.sony-europe.com
For
customers
in
Latin
America:
http://esupport.sony.com/ES/LAI
For
customers
in
Pan
Asia:
http://www.sony-asia.com/section/support
http://www.sony-asia.com/caraudio/
The power antenna (aerial) does not extend.
The power antenna (aerial) does not have a relay box.
No sound.
• The
ATT
function
is
activated, or the Telephone
ATT
function (when the interface cable
of
a telephone
is
connected
to
the
ATT
lead)
is
activated.
• The position
of
the fader control "FAD"
is
not set for
a 2-speaker system.
No beep sound.
• The beep sound
is
canceled (page
17).
• An optional power amplifier
is
connected and you are
not using the built-in amplifier.
The contents
of
the memory have been erased.
• The RESET button has been pressed.
-+
Store again into the memory.
• The power supply lead or battery has been
disconnected or it
is
not connected properly.
Stored stations and correct time are erased.
The fuse has blown.
Makes noise when the position
of
the ignition
is
switched.
The leads are not matched correctly with the boat's
accessory power connector.
continue
to
next page
--+
-
23
To Next Page
Loading...
