Sony RCD-W10 User Manual

8
AMS
Playing a CD
This unit has two decks.
In this manual, the CD player section is just
called DECK A, and the CD-R and CD-RW
recording section is called DECK B.
When using the remote, set SELECT to CD for
operations on DECK A (the CD player
section), or to CDR for operations on DECK B
(the CD-R or CD-RW recording section).
1 Turn on the amplifier and adjust the
volume to the minimum.
2 Set the function of the connected
amplifier with its input selector.
3 Press POWER.
4 Press OPEN/CLOSE (or one of the DISC
1-5 A buttons for DECK A of RCD-
W50C) and place a disc on the inner
circle of DECK A (or B). Press OPEN/
CLOSE (or A) again to close the disc
tray.
5 For DECK A of RCD-W50C, press PLAY
MODE repeatedly to select the
Continuous play mode.
When you
select
ALL DISCS
1 DISC
6 Press H.
The unit starts playing. Adjust the volume on
the amplifier.
Basic Operations
POWER
OPEN/CLOSE
H
With the label side up
The unit plays
All discs in the unit consecutively
in the order of the disc number.
Only one disc you have selected.
DISC 1-5 A
(OPEN/CLOSE for RCD-W10)
AMS
H
PLAY MODE
To
Stop playback
Pause playing
Select the disc
(for DECK A of
RCD-W50C)
Go to the next disc
(for DECK A of
RCD-W50C) Z
Go to the next
track
Go to the beginning
of the current track
or the preceding
track
Remove the disc
* When the disc is in the unit, the indicator lights up
in orange, then it turns green when the disc is selected.
**AMS: Automatic Music Sensor
Tips
• You can start playing with the track selected in Step 6.
1 Turn AMS (or press ./> or the number
buttons on the remote) to select the track you
want to play using the display*.
2 Press H.
*See “Using the Display” on page 9.
• You can remove or load discs while playing the
other deck. Press OPEN/CLOSE (or A) of the deck
that is not currently playing to open that tray, and
remove or load a disc.
• The DISC 1-5 button indicator lights up when the
disc is in the tray. The indicator turns to green when
the disc is selected.
• You can connect a headphone to the PHONE jack
on the front panel. Turn the PHONE LEVEL
control to adjust the volume.
• You can replace any discs in the other disc trays
while playing a disc in DECK A of RCD-W50C.
Press OPEN/CLOSE (or A) of the deck that is not
currently playing to open that tray, and remove or
load a disc.
Notes
• You can play unfinalized CD-Rs or CD-RWs only
in DECK B. For the detailed explanation about
finalizing, see “Finalizing a CD-R or CD-RW” on
page 24.
• Do not leave the disc tray open when the unit is not
in use to prevent dust and dirt from entering and
prevent damage to the disc tray.
• When you turn on the unit, you will hear some
mechanical noise from the unit. This is not a
malfunction.
Do the following:
Press x.
Press X. Press the button again or
press H to resume playing.
Press one of the DISC 1-5
buttons.*
Press D. SKIP on the remote.
Turn AMS**clockwise (or press
> on the remote ).
Turn AMS counterclockwise (or
press . on the remote).
Press
OPEN/CLOSE (or A),
whichever contains the disc you
want to remove after stopping
play.
X
X
x
x

Sony RCD-W10 Specifications

Power

North American model power requirements	120 V AC, 60 Hz
Mexican model power requirements	120 V AC, 60 Hz
Other models power requirements	110-120/220-240V AC, 50/60 Hz
Power consumption	25 W

Inputs

ANALOG IN impedance	47 kilohms
ANALOG IN rated input	500 mVrms
ANALOG IN minimum input	250 mVrms

Outputs

ANALOG OUT impedance	47 kilohms
ANALOG OUT rated output	2 Vrms
ANALOG OUT load impedance	over 10 kilohms

Weight and Dimensions

dimensions	430 × 108 × 399 mm
RCD-W50C mass	6.8 kg
RCD-W10 mass	6.0 kg