11
STR-K7000
SECTION 3
TEST MODE
FACTORY PRESET MODE
* All preset contents are reset to the default setting.
* Procedure:
While depressing the [SPEAKERS $OFF/A/B/A+B%] and the
[MOVIE] buttons simultaneously, press the
?/1 button to turn
on the main power.
The message “FACTORY” appears for a moment and the present
contents are reset to the default values.
AM CHANNEL STEP 9 kHz/10 kHz SELECTION
MODE
* Either the 9 kHz step or 10 kHz step can be selected for the AM
channel step.
* Procedure:
Turn the [INPUT SELECTOR] control to set AM and press the
?/1 button to turn off the main power.
While depressing the [TUNING MODE] button, press the ?/1
button to turn on the main power.
Either the message “9k STEP” or “10k STEP” appears for a
moment and select the desired step.
VACUUM FLUORESCENT DISPLAY TEST MODE
* All fluorescent segments are tested.
When this test is activated, all segments light on at the same
time, then each segment lights on one after another.
* Procedure:
While depressing the [TUNING MODE] and the [DISPLAY] but-
tons simultaneously, press the ?/1 button to turn on the main
power.
1. ALL segments light on.
[MULTI CHANNEL DECODING] LED light on.
2. Turn the [INPUT SELECTOR] control, confirm display.
3. Turn the [INPUT SELECTOR] control, confirm display.
[MULTI CHANNEL DECODING] LED light on.
4. Turn the [INPUT SELECTOR] control, all segments and all LEDs
light off.
SOUND FIELD CLEAR MODE
* The preset sound field is cleared when this mode is activated.
Use this mode before returning the product to clients upon
completion of repair.
* Procedure:
While depressing the [2CH] button, press the ?/1 button to turn
on the main power.
The message “S.F. CLR.” appears for a moment and initializa-
tion is performed.
SOFTWARE VERSION DISPLAY MODE
* The software version is displayed.
* Procedure:
While depressing the [SPEAKERS $OFF/A/B/A+B%] and the
[DISPLAY] buttons simultaneously, press the ?/1 button to turn
on the main power.
The model name, destination and the software version are dis-
played for a moment.
KEY CHECK MODE
* Button check
* Procedure:
While depressing the [SPEAKERS $OFF/A/B/A+B%] and the [2CH]
buttons simultaneously, press the ?/1 button to turn on the main
power.
Either the message “REST 13” appears.
Every pressing of any button other than the ?/1 counts down
the buttons. The buttons which are already counted once are not
counted again. When all buttons are pressed “REST 00” appears.
COMMAND MODE SELECTION MODE
* The command mode (AV1 or AV2) of the remote commander
can be selected.
* Procedure:
While depressing the [INPUT MODE] button, press the
?/1 but-
ton to turn on the main power.
Either the message “C.MODE.AV 1” or “C.MODE.AV 2” ap-
pears for a moment and select the desired mode.
L
SW
LFE
CR
SL S SR
SBL SB SBR
SP A
SP B SLEEP OPT COAX HDMI 96/24
DIGITAL EX PRO LOGIC II x DTS-ES NEO:6 AAC CAT RDS
D.RANGE EQ STEREO MONO
A.DIRECT
D
D
D
D
dB
k Hz
m ft.
MHz
MEMORY
L
SW
LFE
R
S
SB
A
SLEEP COAX 96/24
EX DTSII NEO:6 CAT
D.RANGE
STEREO
dB
Hz
ft.
MEMORY
C
SL SR
SBL SBR
SP
SP B OPT HDMI
DIGITAL xPRO LOGIC -ES AAC RDS
EQ MONO
A.DIRECT
D
D
D
D
k
m
MHz
To Next Page