STR-KS2000
59
HDMI RE BOARD IC3519 M30620FCPGP-RNU04 (HDMI CONTROLLER)
Pin No. Pin Name I/O Description
1 to 5 NC - Not used
6 BYTE - Not used
7 CNVSS I Processor mode switch input terminal (for test)
8, 9 NC - Not used
10 RESET I System reset signal input from the main system controller "L": reset
11 XOUT O System clock output terminal (10 MHz)
12 VSS - Ground terminal
13 XIN I System clock input terminal (10 MHz)
14 VCC_3.3V - Power supply terminal (+3.3V)
15 NMI - Not used
16 to 18 NC - Not used
19 RX_RST O System reset signal output to the HDMI receiver "L": reset
20 RX_INT I Interrupt status input from the HDMI receiver
21 RX_HPD1 O Hot plug connection detect signal output to the HDMI input selector
22 to 26 NC - Not used
27 CSCL O Serial data transfer clock signal output to the HDMI section
28 CSDA I/O Two-way data bus with the HDMI section
29 232COUT O Serial data output terminal for the RS-232C
30 232CIN I Serial data input terminal for the RS-232C
31, 32 NC - Not used
33 TX I UART data input from the system controller
34 RX O UART data output to the system controller
35 EEPROMSEL1 O Write enable signal output to the EEPROM
36 to 39 NC - Not used
40 VDAC_RESET - Not used
41 TX_5VPWR O Power on/off control signal output terminal "H": power on
42 TX_RST I Interrupt status input from the HDMI transceiver
43 TX_INT O System reset signal output to the HDMI transceiver "L": reset
44 to 50 NC - Not used
51 to 53 TMDS_S1 to TMDS_S3 O Source selection signal output to the HDMI input selector
54 TMDS_OEB O Output enable signal output to the HDMI input selector
55, 56 P5V_SELA, P5V_SELB O HDMI SAT IN, DVD IN, VEDEO 2/BD IN jack detection signal select signal output terminal
57 to 59 NC - Not used
60 VCC_3.3V - Power supply terminal (+3.3V)
61 NC - Not used
62 VSS - Ground terminal
63, 64 NC - Not used
65 MUTE O Audio muting signal output terminal
66 AD_SW - Not used
67 AD_INT - Not used
68 AD_RST - Not used
69 PROUT_RST - Not used
70 PROU_OUT_SW - Not used
71 to 90 NC - Not used
91 to 93
MODEL_SW3 to
MODEL_SW1
I Model setting terminal
94 AVSS - Ground terminal
95 NC - Not used
96 VREF I Reference voltage (+3.3V) input terminal
97 AVCC - Power supply terminal (+3.3V)
98 to 100 NC - Not used
w
w
w
.
x
i
a
o
y
u
1
6
3
.
c
o
m
Q
Q
3
7
6
3
1
5
1
5
0
9
9
2
8
9
4
2
9
8
T
E
L
1
3
9
4
2
2
9
6
5
1
3
9
9
2
8
9
4
2
9
8
0
5
1
5
1
3
6
7
3
Q
Q
TEL 13942296513 QQ 376315150 892498299
TEL 13942296513 QQ 376315150 892498299
http://www.xiaoyu163.com
http://www.xiaoyu163.com
To Next Page
Loading...
