158
DME Wipe Pattern Variation and
Modifiers
You can apply the following changes and modifiers to the
selected DME wipe pattern in the same way as for an
ordinary wipe pattern.
For details about the method of operation, see “Setting
DME Wipe Modifiers” (page 161) and “Setting
Independent Key Transition DME Wipe Modifiers”
(page 165).
Direction: You can set the DME wipe direction to normal,
reverse, or alternating normal/reverse (see page 161).
However, this can be specified for a key transition only
when the following patterns are selected.
• 1204, 1207, 1221 to 1224, 7204, 7207, 7221 to 7224
When pattern numbers 1201, 1202, 1203, 1205, 1206,
1208, 1209, 1225, 1251, 1701, and 1702 are selected,
Direction cannot be used.
Edge: You can apply a border or soft border (see
page 162).
In the case of user programmable DME patterns for
keys in which an edge has already been applied to the
effect, the behavior is as follows.
• When the DME wipe edge is enabled, only part of
the edge applied in the effect is enabled, and that
portion can be adjusted.
• When the DME wipe edge setting is disabled, the
edge applied in the effect is applied as-is.
When pattern numbers 1011, 1012, 1013, 1701, and
1702 are selected, Edge cannot be used.
Positioner: You can move the DME wipe pattern or center
of the effect to an arbitrary position (see page 162).
Using the position select function, you can also
instantaneously move the pattern (see page 162).
This can only be used when one of the following
pattern numbers is selected.
• 1031, 7031
As the transition progresses, the pattern center
automatically moves initially from the set position
toward the center of the screen. In other words, the
effect obtained is the same as in a normal wipe with
the positioner set to [Auto Center].
• 1032, 1033
You can set the position of the pattern at the start of
the transition. As the transition, which starts after the
dead band, progresses, the pattern automatically
moves from the initial position toward the center of
the screen.
• 1201 to 1209, 1221 to 1225, 1251, 7201 to 7208,
7221 to 7224
You can set the pattern position when the first
transition completes.
• 1381, 1391, 1393, 1394, 1396
You can set the center of the transition effect.
3D Trans 1ch 1071, 1072, 1074, 1076, 1077, 1088,
1091 to 1094
Ye s Ye s Ye s
2ch 2631 to 2634, 2642, 2644 Yes No No
Sparkle 1ch 1391, 1393, 1394, 1396, 1398, 1399 Yes Yes Yes
Split Slide 1ch 1384 to 1389 Yes Yes Yes
Mosaic 1ch 1701 Yes No No
Defocus 1ch 1702 Yes No No
Crop Slide 2ch 2661, 2662 Yes No No
Brick 2ch 2801 to 2804, 2811 to 2814 Yes No No
3ch 3601 Yes No No
User Program 1ch 1901 to 1999 Yes Yes Yes
2ch 2901 to 2999 Yes No No
3ch 3901 to 3999 Yes No No
Resizer Slide 1ch 7001 to 7008 No Yes Yes
Resizer Squeeze 1ch 7021 to 7031 No Yes Yes
Resizer Frame I/O 1ch 7201 to 7208, 7221 to 7224 No Yes Yes
Pattern group Execution
mode
Pattern number DME wipes for common
transitions
DME wipes for
independent key
transitions
Background Key
Note
Note
To Next Page
Loading...
