How to fix OUTOFRNG error on Spirax Sarco SP7-11?
If your Spirax Sarco Valve Positioners display 'OUTOFRNG', the mounting conditions may not be correct, or the position is outside the sensor range. Verify the mounting conditions.
What to do if Spirax Sarco SP7-11 show ERROR 13?
If the Spirax Sarco Valve Positioners displays ERROR 13, it indicates an invalid input current. To resolve this, check the power source and the wiring.
Why does Spirax Sarco SP7-11 show TIMEOUT error?
If the Spirax Sarco Valve Positioners displays 'TIMEOUT', it means the automatic adjustment function is taking too long. To resolve this, increase the supply pressure or use boosters.
What to do if Spirax Sarco SP7-11 Valve Positioners show ERROR 11?
If the Spirax Sarco Valve Positioners display ERROR 11, it indicates that the supply voltage has fallen below the minimum voltage. To fix this, check the power source and the wiring.
What to do if Spirax Sarco Valve Positioners show ERROR 10?
If your Spirax Sarco Valve Positioners show ERROR 10, it means the supply voltage was interrupted for at least 20 ms. To resolve this, check the power source and the wiring.
Why does my Spirax Sarco Valve Positioners show CALC_ERR error?
If the Spirax Sarco Valve Positioner displays 'CALC_ERR', this could be due to inconsistent data (e.g., a low value being higher than a high value) or incorrect configuration. You can correct the values or load the factory settings. Another cause could be that data cannot be saved locally because PROFIBUS saves data in the background. In this case, try again later.
How to reset the stroke counter on Spirax Sarco SP7-11 Valve Positioners (ALARM 6)?
To reset the counter on Spirax Sarco Valve Positioners after ALARM 6, you need to use a connected PC with suitable software.
What to do if Spirax Sarco SP7-11 display ERROR 23?
If the Spirax Sarco Valve Positioners display ERROR 23, it indicates an error when verifying the checksum of the configuration data (RAM). If the error persists even after the positioner has been reset, the device will need to be returned to the manufacturer for repair.
What to do if Spirax Sarco SP7-11 Valve Positioners display ERROR 22?
If the Spirax Sarco Valve Positioners display ERROR 22, it indicates an error during the table processing, pointing to an error in the working data (RAM). If the error persists even after the positioner has been reset, the device will need to be returned to the manufacturer for repair.
What to do if Spirax Sarco Valve Positioners display ERROR 21?
If the Spirax Sarco Valve Positioners display ERROR 21, it indicates an error while processing the measured values, pointing to an error in the working data (RAM). If the error persists even after the positioner has been reset, the device will need to be returned to the manufacturer for repair.
Details of error codes, their causes, and troubleshooting.
Specific error messages for SP7-11/12 and SP7-21/22 models.
List of alarm codes, their possible causes, and troubleshooting.
Codes and descriptions for various system messages.
Procedures for diagnosing and resolving positioner issues.
Explanation of signal words DANGER, WARNING, CAUTION, and NOTE.
Safety precautions to be followed during operation.
Detailed parameter descriptions for HART communication.
Parameter details for Profibus PA and Foundation Fieldbus.
Parameter mapping for Profibus PA and Foundation Fieldbus devices.
Setting the PROFIBUS bus address for communication.
General| Input Signal | 4-20 mA |
|---|---|
| Output Pressure | 0 to 100% of supply pressure |
| Supply Pressure | 20-100 psi (1.4-7.0 bar) |
| Enclosure Rating | IP66 (NEMA 4X) |
| Ambient Temperature | -40 to 85°C (-40 to 185°F) |
| Mounting | Direct mounting to actuator |
| Materials | Aluminum |
| Type | Electropneumatic positioner |
| Action | Direct or Reverse |
To Next Page
