What should I do if Spirax Sarco Valve Positioners display ERROR 50 to 99?
If your Spirax Sarco Valve Positioners display an error within the range of ERROR 50 to 99, it indicates an internal error. If the error can be reproduced and occurs in the same position after resetting, the device must be returned for repair to the manufacturer.
What does ALARM 4 mean on Spirax Sarco SP7-11 Valve Positioners?
ALARM 4 on Spirax Sarco Valve Positioners indicates that controlling is inactive because the device does not operate in control mode or the binary input is active. To resolve this, switch to control mode or switch off the binary input.
What to do if Spirax Sarco Valve Positioners show ERROR 20?
If your Spirax Sarco Valve Positioners display ERROR 20, it indicates that there is no access possible to the data in the EEPROM. If resetting the device doesn't restore access, load the factory settings. If the error persists, the device must be returned for repair to the manufacturer.
What causes ALARM 1 on Spirax Sarco Valve Positioners?
ALARM 1 on Spirax Sarco Valve Positioners is caused by leakage between the positioner and the actuator. To address this, check the piping.
What to do if Spirax Sarco SP7-11 display ALARM 3?
If the Spirax Sarco Valve Positioners are showing ALARM 3, it means there is an alarm from the zero monitor, indicating that the zero position has shifted by more than 4%. To solve this, correct the mounting.
What to do if Spirax Sarco Valve Positioners display ERROR 12?
If your Spirax Sarco Valve Positioners are displaying ERROR 12, it indicates that the position is outside the measuring range, possibly due to a malfunction in the position sensor. Check the mounting to resolve this issue.
How to fix ERROR 13 on Spirax Sarco Valve Positioners?
ERROR 13 on Spirax Sarco Valve Positioners indicates an invalid input current, which occurs when the setpoint signal is overridden. To resolve this, check the power source and the wiring.
What to do if Spirax Sarco Valve Positioners display ERROR 11?
If the Spirax Sarco Valve Positioners are showing ERROR 11, it means the supply voltage has fallen below the minimum voltage. To solve this, check the power source and the wiring.
Why is my Spirax Sarco SP7-11 Valve Positioners showing ALARM 2?
Your Spirax Sarco Valve Positioners are showing ALARM 2 because the setpoint current is outside the permissible range, specifically less than 3.8 mA or greater than 20.5 mA. To fix this, check the power source.
What to do if Spirax Sarco Valve Positioners display ERROR 10?
If your Spirax Sarco Valve Positioners are showing ERROR 10, it indicates that the supply voltage was interrupted for at least 20 ms. This error is displayed after resetting the device to indicate the reason for the reset. You should check the power source and the wiring to solve this problem.
Details of error codes, their causes, and troubleshooting.
Specific error messages for SP7-11/12 and SP7-21/22 models.
List of alarm codes, their possible causes, and troubleshooting.
Codes and descriptions for various system messages.
Procedures for diagnosing and resolving positioner issues.
Explanation of signal words DANGER, WARNING, CAUTION, and NOTE.
Safety precautions to be followed during operation.
Detailed parameter descriptions for HART communication.
Parameter details for Profibus PA and Foundation Fieldbus.
Parameter mapping for Profibus PA and Foundation Fieldbus devices.
Setting the PROFIBUS bus address for communication.
General| Input Signal | 4-20 mA |
|---|---|
| Output Pressure | 0 to 100% of supply pressure |
| Supply Pressure | 20-100 psi (1.4-7.0 bar) |
| Enclosure Rating | IP66 (NEMA 4X) |
| Ambient Temperature | -40 to 85°C (-40 to 185°F) |
| Mounting | Direct mounting to actuator |
| Materials | Aluminum |
| Type | Electropneumatic positioner |
| Action | Direct or Reverse |
To Next Page
