Spirax Sarco SP7-11 - User Manual

64 pages

Save Page as PDF

To Next Page

IM-S51-07 CTLS Issue 1

SP7-10, SP7-11, SP7-12 and SP7-20, SP7-21, SP7-22 Parameterization

SP7-10, SP7-11, SP7-12 and

SP7-20, SP7-21, SP7-22

Parameterization

IM-S51-07

CTLS Issue 1

Device firmware version 05: SP7-10 / SP7-20

Device firmware version 03: SP7-11 / SP7-12 / SP7-21 / SP7-22

Main Page

Other manuals for Spirax Sarco SP7-11

Installation And Maintenance Instructions72 pages

Quick Start Guide12 pages

Questions and Answers

F
Frederick HarrisAug 25, 2025
What to do if Spirax Sarco SP7-11 show ALARM 5?
- B
  Brian PayneAug 26, 2025
  If the Spirax Sarco Valve Positioners display ALARM 5, it means positioning has timed out because the settling time needed exceeds the configured stroke time. To resolve this, ensure that the actuator is not blocked, the supply air pressure is adequately high, and the specified time limit is higher than 1.5 times the longest stroke time of the actuator. If adaption cannot run uninterruptedly for an actuator, adaption should be switched on until the alarm does not occur anymore during controlling actions.
E
Edward CollinsAug 25, 2025
How to reset the travel counter on Spirax Sarco SP7-11 Valve Positioners (ALARM 7)?
- E
  Elizabeth MooreAug 25, 2025
  To reset the travel counter on Spirax Sarco Valve Positioners after ALARM 7, use a connected PC with suitable software.

Summary

4. Diagnosis and Error Messages

4.1 a Error Codes

Details of error codes, their causes, and troubleshooting.

4.1 b Specific SP7-11;12 and SP7-21;22 Error Messages

Specific error messages for SP7-11/12 and SP7-21/22 models.

4.2 Alarm Codes

List of alarm codes, their possible causes, and troubleshooting.

4.3 Message Codes

Codes and descriptions for various system messages.

4.4 Error Handling

Procedures for diagnosing and resolving positioner issues.

1. General Information

1.2 Warnings

Explanation of signal words DANGER, WARNING, CAUTION, and NOTE.

2. Operation

2.1 Safety Instructions

Safety precautions to be followed during operation.

2.2 Parameterization of the Device

2.6 Operating Modes

2.7 Inhibiting Operation

3. Configuration

3.3 4.20 mA and 4-20 mA HART Parameter Descriptions (SP7-10 and SP7-20)

Detailed parameter descriptions for HART communication.

3.5 Parameter Group 1: Standard

3.6 Parameter Group 2: Setpoint

3.7 Parameter Group 3: Operating Range

3.8 Parameter Group 4: Messages

3.9 Parameter Group 5: Alarms

3.10 Parameter Group 6: Manual Adjustment

3.11 Parameter Group 7: Control Parameters

3.12 Parameter Group 8: Analog Output

3.13 Parameter Group 9: Digital Output

3.14 Parameter Group 10: Digital Input

3.15 Parameter Group 11: Safe Position

3.16 Profibus PA and Foundation Fieldbus Parameter Descriptions (SP7-11, SP7-12 and SP7-21, SP7-22) - PROFIBUS PA and Foundation Fieldbus Parameter

Parameter details for Profibus PA and Foundation Fieldbus.

3.17 Profibus PA and Foundation Fieldbus Parameter Descriptions (SP7-11, SP7-12 and SP7-21, SP7-22)

Parameter mapping for Profibus PA and Foundation Fieldbus devices.

3.18 Specific Parameters for Digital BUS Communication Versions Only: - P1.5 ADRESS - Bus Address (PROFIBUS PA Version Only)

Setting the PROFIBUS bus address for communication.

3.19 P7.4 GOPULSE^ Go Pulse (Up)

3.20 P7.5 GOPULSEV Go Pulse (Down)

Spirax Sarco SP7-11 Specifications

General

Input Signal	4-20 mA
Output Pressure	0 to 100% of supply pressure
Supply Pressure	20-100 psi (1.4-7.0 bar)
Enclosure Rating	IP66 (NEMA 4X)
Ambient Temperature	-40 to 85°C (-40 to 185°F)
Mounting	Direct mounting to actuator
Materials	Aluminum
Type	Electropneumatic positioner
Action	Direct or Reverse