SPXFLOW C Series - Page 57

Parts Lists Waukesha Cherry-Burrell
®
Brand C-Series Pump
01/2019 95-03008-IEC Page 57
C-114 Pump Parts
Notes:
* Recommended Spare Parts - also available in kits (see page 74)
1. For casings with Bevel threaded, Female I-Line, NPT or Flanged connections, please contact factory.
2. These items are needed to change the motor adapter.
4. Contact factory if casing drain, passivation, or optional finish is required.
5. For a pump shipped prior to approx. April 1999: item 11 or item 71 alone will not work; need both backplate (item 11)
and adapter (item 71) as well as the casing O-ring (item 90). Contact factory with serial no.
9. Applies only to the Sealed Impeller Design.
10. Does not apply to the Sealed Impeller Design; applies only to the Pin Impeller Design.
11. Contact your local distributor for other impeller sizes and finishes.
12. Type “F” seal is a type “D” seal with a water cascade attachment.
ITEM DESCRIPTION QTY. PART NO. NOTES
Casing, 1,5" x 1,5" (38,1 x 38,1 mm) with ISO 2852 clamp 60001+
Casing, 2" x 1,5" (50,8 x 38,1 mm) with ISO 2852 clamp 60002+
C114 Impeller - Pin Impeller Design, Full, 4,0" (101,6 mm) dia., 32
Ra finish
60027+ 10, 11
C114 Impeller - Sealed Impeller Design, Full, 4,0" (101,6 mm) dia.,
32 Ra finish
138527+ 9, 11
3
Impeller Nut - Sealed Impeller Design 1 138532+ 9
Impeller Nut O-rin
g
- Sealed Impeller Desi
g
n, BUNA N
N70015
Impeller Nut O-rin
g
- Sealed Impeller Desi
g
n, FKM
V70015
Impeller Nut O-rin
g
- Sealed Impeller Desi
g
n, EPDM
E70015
Shaft Collar, Sealed Impeller Design, D71 Frame 138567+
Shaft Collar, Sealed Impeller Design, D80 Frame 138568+
Shaft Collar, Sealed Impeller Design, D90L Frame 135578+
Stub Shaft, D71 Frame 60521E
Stub Shaft, D80 Frame 60522E
Stub Shaft, D90L Frame 60523E
Stub Shaft, Sealed Impeller Design, D71 Frame 138541+
Stub Shaft, Sealed Impeller Design, D80 Frame 138542+
Stub Shaft, Sealed Impeller Design, D90L Frame 138543+
Shaft Setscrew, for D71/D80 Frame Stub Shafts 30-714
Shaft Setscrew, for D90L Frame Stub Shafts 30-715
7
Impeller Key - Sealed Impeller Design 1 138585+ 9
Stub Shaft O-rin
g
- Sealed Impeller Desi
g
n, BUNA N
N70015
Stub Shaft O-rin
g
- Sealed Impeller Desi
g
n, FKM
V70015
Stub Shaft O-rin
g
- Sealed Impeller Desi
g
n, EPDM
E70015
11
Backplate 1 60010+ 4, 5, 8
11F
Backplate Pin 2 60013+ 8
* 24 Impeller Retaine
r
1 60039+
Deflector, D71/D80 Frame 60042+
Deflector, D90L Frame 60044+
PL5050-CH10
2
1
6A
40
1 1, 4
10
9
2, 101
*4
1
*8
1
1
9
1
9
5
19
2, 10
6
3