SPXFLOW C Series - Page 61

Parts Lists Waukesha Cherry-Burrell
®
Brand C-Series Pump
01/2019 95-03008-IEC Page 61
C-216 Pump Parts
Notes:
* Recommended Spare Parts - also available in kits (see page 74)
1. For casings with Bevel threaded, Female I-Line, NPT or Flanged connections, please contact factory.
2. These items are needed to change the motor adapter.
4. Contact factory if casing drain, passivation, or optional finish is required.
5. Used with standard "D" seal only.
6. Optional motor shrouds available for these frame sizes only.
7. Shown with standard type “D” Seal. For other optional seals, see page 72 and page 73.
8. Backplate pins (11F) are included with the backplate if purchased as a spare part.
9. Applies only to the Sealed Impeller Design.
10. Does not apply to the Sealed Impeller Design; applies only to the Pin Impeller Design.
11. Contact your local distributor for other impeller sizes and finishes.
12. Type “F” seal is a type “D” seal with a water cascade attachment.
ITEM DESCRIPTION QTY. PART NO. NOTES
Casing, 2" x 1-1/2" (50,8 x 38,1 mm) with ISO 2852 clamp 1 60003+ 1, 4
Casing, 2-1/2" x 1-1/2" (63,5 x 38,1 mm) with ISO 2852 clamp 1 60004+ 1, 4
C216 Impeller - Pin Impeller Design, Full, 6,0" (152,4 mm) dia.,
32 Ra finish
60028+ 10, 11
C216 Impeller - Sealed Impeller Design, Full, 6,0" (152,4 mm)
dia., 32 Ra finish
138528+ 9, 11
3
Impeller Nut - Sealed Impeller Design 1 138533+ 9
Impeller Nut O-rin
g
- Sealed Impeller Desi
g
n, BUNA N
N70118
Impeller Nut O-rin
g
- Sealed Impeller Desi
g
n, FKM
V70118
Impeller Nut O-rin
g
- Sealed Impeller Desi
g
n, EPDM
E70118
Shaft Collar - Sealed Impeller Design, D80 Frame 138568+
Shaft Collar - Sealed Impeller Design, D90 Frame 135578+
Shaft Collar - Sealed Impeller Design, D100L/D112M Frame 135580+
Shaft Collar - Sealed Impeller Design, D132S Frame 135699+
Stub Shaft, D80 Frame 60524E
Stub Shaft, D90 Frame 60525E
Stub Shaft, D100L/D112M Frame 60526E
Stub Shaft, D132S Frame 60527E
Stub Shaft, Sealed Impeller Design, D80 Frame 138568+
Stub Shaft, Sealed Impeller Design, D90 Frame 135578+
Stub Shaft, Sealed Impeller Design, D100L/D112M Frame 135580+
Stub Shaft, Sealed Impeller Design, D132S Frame 135699+
Shaft Setscrew, D80 Frame 30-714
Shaft Setscrew, D90/D100L/D112M Frame 30-715
Shaft Setscrew, D132S Frame 30-716
7
Impeller Key - Sealed Impeller Design 1 138586+ 9
Stub Shaft O-rin
g
- Sealed Impeller Desi
g
n, BUNA N
N70118
Stub Shaft O-rin
g
- Sealed Impeller Desi
g
n, FKM
V70118
Stub Shaft O-rin
g
- Sealed Impeller Desi
g
n, EPDM
E70118
11
Backplate 1 60011+ 4, 5, 8
11F
Backplate Pin 2 60013+ 8
* 24 Impeller Retaine
r
1 60040+
Deflector, D80/D90/D100L/D112M Frame 60045+
Deflector, D132S Frame 60046+
PL5050-CH11
40
110
6A
310
*8
19
9
5
19
6
1
10
9
1
2
1
*4
1