SPXFLOW C Series - Page 65

Parts Lists Waukesha Cherry-Burrell
®
Brand C-Series Pump
01/2019 95-03008-IEC Page 65
C-218 Pump Parts
Notes:
* Recommended Spare Parts - also available in kits (see page 74)
1. For casings with Bevel threaded, Female I-Line, NPT or Flanged connections, please contact factory.
2. These items are needed to change the motor adapter.
4. Contact factory if casing drain, passivation, or optional finish is required.
5. Used with standard "D" seal only.
6. Optional motor shrouds available for these frame sizes only.
7. Shown with standard type “D” Seal. For other optional seals, see page 72 and page 73.
8. Backplate pins (11F) are included with the backplate if purchased as a spare part.
9. Applies only to the Sealed Impeller Design.
10. Does not apply to the Sealed Impeller Design; applies only to the Pin Impeller Design.
11. Contact your local distributor for other impeller sizes and finishes.
12. Type “F” seal is a type “D” seal with a water cascade attachment.
ITEM DESCRIPTION QTY. PART NO. NOTES
Casing, 2" x 1,5" (50,8 x 38,1 mm) with ISO 2852 clamp 60005+
Casing, 3" x 1,5" (76,2 x 38,1 mm) with ISO 2852 clamp 60006+
C218 Impeller - Sealed Impeller Design, Full, 7,875" (203,2 mm)
dia., 32 Ra finish
60029+ 10, 11
C218 Impeller - Pin Impeller Design, Full, 7,875" (203,2 mm)
dia., 32 Ra finish
138529+ 9, 11
3
Impeller Nut - Sealed Impeller Design 1 138534+ 9
Impeller Nut O-rin
g
- Sealed Impeller Desi
g
n, BUNA N
N70124
Impeller Nut O-rin
g
- Sealed Impeller Desi
g
n, FKM
V70124
Impeller Nut O-rin
g
- Sealed Impeller Desi
g
n, EPDM
E70124
Shaft Collar - Sealed Impeller Design, D90L Frame 135578+
Shaft Collar - Sealed Impeller Design, D100L/D112M Frame 135580+
Shaft Collar - Sealed Impeller Design, D132S Frame 135699+
Shaft Collar - Sealed Impeller Design, D160M/L Frame 135700+
Stub Shaft, D90L Frame 60528E
Stub Shaft, D100L/D112M Frame 60529E
Stub Shaft, D132S Frame 60530E
Stub Shaft, D160M/L Frame 60531E
Stub Shaft, Sealed Impeller Design, D90L Frame 138562+
Stub Shaft, Sealed Impeller Design, D100L/D112M Frame 138563+
Stub Shaft, Sealed Impeller Design, D132S Frame 138564+
Stub Shaft, Sealed Impeller Design, D160M/L Frame 138565+
Shaft Setscrew, D90L/D100L/D112M Frame 30-715
Shaft Setscrew, D132S/D160M/L Frame 30-716
7
Impeller Key - Sealed Impeller Design 1 138587+ 9
Stub Shaft O-rin
g
- Sealed Impeller Desi
g
n, BUNA N
N70124
Stub Shaft O-rin
g
- Sealed Impeller Desi
g
n, FKM
V70124
Stub Shaft O-rin
g
- Sealed Impeller Desi
g
n, EPDM
E70124
11
Backplate 1 60012+ 4, 5, 8
11F
Backplate Pin 2 60013+ 8
* 24 Impeller Retaine
r
1 60041+
Deflector, D90L Frame 60047+
Deflector, D100L/D112M/D132S Frame 60046+
Deflector, D160M/L Frame 60049+
PL5050-CH12
110
*8
19
40
6A
1
1, 4
2, 10
2, 103
2
1
9
9
5
19
1
6
1
*4
1