Stanley STST1825 User Manual

40 • ENGLISH
TROUBLESHOOTING
Problem Possible Cause Solution
Saw will not start
1. Saw is not plugged in
2. Blown fuse or circuit breaker
3. Cord is damaged
4. Debris in ON/OFF switch
1. Plug into power source
2. Replace fuse or reset circuit breaker
3. Have power cord replaced by authorized
service center
4. Clean any accumulated debris
Does not make accurate 45° and
90° rip cuts
1. Positive stop not adjusted
2. Blade angle pointer not set
accurately
1. Check blade with square and adjust
2. Check blade with square and adjust
blade angle pointer
Material pinched blade when
ripping
1. Rip fence is not aligned with
blade
2. Warped wood, edge against
fence is not straight
1. Check and adjust the rip fence
2. Select another piece of wood
Material binds on splitter
1. Splitter not correctly in line with
blade
1. Check and align the splitter with blade
Saw makes unsatisfactory cuts
1. Dull blade
2. Blade mounted backward
3. Gum or resin on blade
4. Incorrect blade for work
1. Replace blade
2. Turn blade around
3. Remove blade and clean
4. Change to correct blade
Material kicked back from the
blade
1. Rip fence is out of adjustment
2. Splitter is not in line with blade
3. Feeding stock without rip fence
4. Dull blade
5. Bevel knob is not tight
1. Align rip fence with miter gauge groove
2. Align splitter with blade
3. Install and use rip fence
4. Replace blade
5. Tighten the knob
Blade does not raise or tilt freely 1. Sawdust and dirt in elevation/
tilting
1. Brush or blow out loose dust and dirt
Blade does not come up to
speed, reset trips too easily
1. Extension cord is too light or too
long
2. Low house voltage
1. Replace extension cord with adequate
size
2. Contact electrician
Saw vibrates excessively 1. Saw is not mounted securely to
work bench
2. Bench or stand is on uneven floor
3. Damaged saw blade
1. Tighten all mounting hardware
2. Re-position on flat, level floor
3. Replace blade
Solamente para propósito de Argentina:
Importado por: Black & Decker Argentina S.A.
Pacheco Trade Center
Colectora Este de Ruta Panamericana
Km. 32.0 El Talar de Pacheco
Partido de Tigre
Buenos Aires (B1618FBQ)
República de Argentina
No. de Importador: 1146/66
Tel.: (011) 4726-4400
Imported by/Importado por:
Black & Decker do Brasil Ltda.
Rod. BR 050, s/n°- Km 167
Dist. Industrial II
Uberaba ˆ MG ˆ Cep: 38064-750
CNPJ: 53.296.273/0001-91
Insc. Est.: 701.948.711.00-98
S.A.C.: 0800-703-4644
Solamente para propósitos de Colombia
Importado por: Black & Decker de Colombia, S.A.
Carrera 85D # 51-65, Bodega 23
Complejo Logístico San Cayetano
Bogotá - Colombia
Tel.: 744-7100
Solamente para propósito de Chile:
Importado por: Black & Decker de Chile, S.A.
Av. Pdte. Eduardo Frei M. 6001-67 Conchalí
Santiago de Chile
Tel.: (56-2) 2687 1700
Impreso en China
Impresso em China
Printed in China
09/09/2014
Solamente para propósito de México:
Importado por: Black and Decker S.A. de C.V.
Avenida Antonio Dovali Jaime
# 70 Torre B Piso 9
Colonia Santa Fé
Delegación Alvaro Obregón,
México D.F. 01210
Tel. (52) 555-326-7100
R.F.C.: BDE810626-1W7
Black & Decker del Perú S.A.
Av. Enrique Meiggs 227.
Pque. Industrial - Callao
Tel.: (511) 614-4242
RUC 20266596805

Stanley STST1825 Specifications

General

Idle speed (max)	4800 RPM
Cutting depth (45º)	56 mm
Cutting depth (90º)	76 mm
Diamond disc	-
Saw blade type	Single blade
Product color	Black, Grey, Yellow

Weight and Dimensions

Depth	505 mm
Width	530 mm
Height	580 mm