► If the mowing lines (2) cannot be pulled out to
the required length: Replace the spool (1) or
the mowing lines (2).
The spool is empty.
13 After Finishing Work
13.1 After finishing work
► Switch off the brushcutter and remove the bat‐
tery.
► If the brushcutter is wet: Allow the brushcutter
to dry.
► If the battery is moist or wet: Allow the battery
to dry, 20.6.
► Clean the brushcutter.
► Clean the deflector.
► Clean the cutting attachment.
► Clean the battery.
► If a metal cutting attachment is attached:
Attach the appropriate transport guard.
14 Transporting
14.1 Transporting the brushcutter
► Switch off the brushcutter and remove the bat‐
tery.
► If a metal cutting attachment is mounted: Fit
the matching transport guard.
Carrying the brushcutter
► Carry the brushcutter in one hand properly
balanced by the shaft, with the cutting attach‐
ment behind you.
Transporting the brushcutter in the car
► Secure the brushcutter to prevent turnover
and movement.
14.2 Transporting the Battery
► Switch off the brushcutter and remove the bat‐
tery.
► Check that the battery is in a safe condition.
► Pack the battery in packaging in such a way
that it cannot move inside the packaging.
► Secure the packaging so that it cannot move.
The battery is subject to the Carriage of Danger‐
ous Goods regulations. The battery is classified
as UN 3480 (lithium ion batteries) and has been
tested pursuant to UN Manual Tests and Criteria
Part III, Subsection 38.3.
The transport regulations can be found at
www.stihl.com/safety-data-sheets.
14.3 Transporting the Charger
► Disconnect the plug from the wall outlet.
► Remove the battery.
► Wind up the connecting cable and attach it to
the charger.
► Transporting the charger in a vehicle: Secure
the charger with lashing straps, belts or a net
to prevent it turning over and moving.
15 Storing
15.1 Storing the brushcutter
► Switch off the brushcutter and remove the bat‐
tery.
► If a metal cutting attachment is mounted:
Attach the appropriate transport guard.
► Ensure that the following conditions are met
when storing the brushcutter:
–
The brushcutter cannot tip over or shift.
–
The brushcutter is out of the reach of chil‐
dren.
–
The brushcutter is clean and dry.
► If you store the brushcutter for more than 30
days: Remove the cutting attachment.
15.2 Storing the Battery
STIHL recommends keeping the battery in a
charging state between 40% and 60 % (2 green
LEDs lit).
► The battery should be stored in such a way
that the following conditions are fulfilled:
–
The battery is out of the reach of children.
–
The battery is clean and dry.
–
The battery is in an enclosed space.
–
The battery is separated from the brushcut‐
ter.
–
If the battery is stored in the charger, dis‐
connect the mains plug and store the bat‐
tery at a state of charge between 40% and
60% (2 lit green LEDs).
–
Do not store the battery outside of the
specified temperature limits,
20.5.
NOTICE
■ If the battery is not stored as described in this
User Manual, the battery may become deeply
discharged and irreparably damaged.
►
Charge a discharged battery before storing
it. STIHL recommends keeping the battery
state of charge between 40% and 60% (2 lit
green LEDs).
►
Store the battery separately from the brush‐
cutter.
15.3 Storing the Charger
► Disconnect the mains plug from the power
supply.
English 13 After Finishing Work
20 0458-027-0101-A
To Next Page
Loading...
Need help?
General
