19.2 Troubleshooting the Charger
Fault LED on
Charger
Cause Remedy
Battery not being
charged.
The LED
flashes red.
No electrical contact
between charger and
battery.
► Remove the battery.
► Clean contacts on charger.
► Insert battery.
There is a malfunction
in the charger.
► Do not use the charger and contact your
STIHL dealer for assistance.
19.3 Product Support and Assis‐
tance on Use
Product support and assistance on use are avail‐
able from STIHL servicing dealers.
For contacts and other information, please visit
https://support.stihl.com or www.stihl.com.
20 Specifications
20.1 STIHL FSA 80.0 R Brushcutter
–
Approved battery: STIHL AK
–
Weight without battery, cutting tool and deflec‐
tor: 4.8 kg
–
Length without cutting tool: 1775 mm
For runtime, see www.stihl.com/battery-life.
20.2 STIHL AK Battery
–
Battery technology: lithium-ion
–
Voltage: 36 V
–
Capacity in Ah: see rating label
–
Energy content in Wh: see rating label
–
Weight in kg: See rating label
20.3 STIHL AL 101 Charger
–
Rated voltage: See rating plate
–
Frequency: see rating plate
–
Rated power: see rating plate
–
Charging current: See rating plate
For charging times, see www.stihl.com/charging-
times.
20.4 Extension Cords
If an extension cord is used, the cross sectional
area of its conductors must meet the following
minimum requirements – depending on the line
voltage and length of the extension cord:
If rated voltage on the rating label is 220V to
240V:
–
Cord length up to 20 m: AWG 15 / 1.5 mm²
–
Cord length 20 m up to 50 m: AWG 13 /
2.5 mm²
If rated voltage on the rating label is 100V to
127V:
–
Cord length up to 10 m: AWG 14 / 2.0 mm²
–
Cord length 10 m up to 30 m: AWG 12 /
3.5 mm²
20.5 Temperature limits
WARNING
■ The battery is not protected against all ambi‐
ent conditions. If the battery is exposed to cer‐
tain environmental conditions, it may catch fire
or explode. This may result in serious injury to
people and damage to property.
►
Do not charge the battery below -20°C or
above +50°C.
► Do not use the brushcutter, battery or
charger below - 20 °C or above + 50 °C.
► Do not store the brushcutter, battery or
charger below -20°C or above +70°C.
20.6 Recommended temperature
ranges
For optimum performance of the brushcutter,
battery and charger, observe the following tem‐
perature ranges:
–
Charging: 5°C to 40°C
–
Use: - 10 °C to + 40 °C
–
Storage: - 20 °C to + 50 °C
If the battery is charged, used or stored outside
the recommended temperature ranges, perform‐
ance may be reduced.
If the battery is wet or moist, allow the battery to
dry for at least 48 h between 15°C and 50°C and
with less than 70% humidity. Higher humidity
may extend the drying time.
20.7 Sound values and vibration val‐
ues
The K value for the sound pressure level is
2 dB(A). The K value for the sound power level is
2 dB(A). The K-value for the vibration level is
2 m/s².
20 Specifications English
0458-027-0101-A 23
To Next Page
Loading...
Need help?
General
