Why does my Stihl Chainsaw cut out during operation?
Your Stihl chainsaw may be cutting out during operation because it is too hot. Engage the chain brake, remove the battery, and allow the chainsaw to cool down for 20 minutes. Alternatively, there may be an electrical fault. In this case, engage the chain brake, remove and refit the battery, then switch on the chainsaw.
Why does my Stihl Chainsaw run time is too short?
If your Stihl chainsaw's run time is too short, it could be due to the battery not being fully charged, so fully charge the battery. Alternatively, the battery life may have been exceeded, indicating it's time to replace the battery.
What to do if the Stihl MSA 60.0 C Chainsaw battery is not being charged?
If your Stihl chainsaw battery isn't charging, there might be no electrical contact between the charger and battery. Remove the battery and clean the contacts on the charger before reinserting the battery. If that doesn't work, there could be a malfunction in the charger. Do not use the charger and contact your STIHL dealer for assistance.
How to start charging Stihl Chainsaw if charging does not start when the battery is inserted into the charger?
If charging doesn't start when you insert the battery into the charger, the battery might be too warm or too cold. Leave the battery inserted in the charger; charging will begin automatically once it reaches the correct temperature range.
Local safety regulations and STIHL safety notes.
Explains DANGER, WARNING, and NOTICE symbols and their meanings.
Explains symbols used in the instruction manual.
Identifies and describes the components of the chainsaw, battery, and charger.
Explains meanings of warning signs and labels on the saw, battery, and charger.
Specifies the intended use of the STIHL MSA 60.0 C / MSA 70.0 C chainsaw.
Outlines requirements and responsibilities for the chainsaw operator.
Details necessary protective clothing and equipment for safe operation.
Covers safety precautions related to the work area and bystanders.
Safety warnings for operating the chainsaw in different environments.
Safety warnings related to the battery's use and exposure.
Safety warnings concerning the operation and placement of the charger.
Details conditions for safe operation of chainsaw components.
Lists criteria for ensuring the chainsaw is in a safe working condition.
Criteria for determining if the guide bar is in a safe condition.
Criteria for ensuring the saw chain is in a safe working condition.
Conditions under which the battery is considered safe to use.
Criteria for ensuring the charger is in a safe condition.
General safety instructions for working with the chainsaw.
Safety precautions and techniques for cutting wood.
Safety guidelines for the process of limbing branches.
Safety precautions and techniques for felling trees.
Explains reactive forces and how to avoid them.
Details causes and prevention of kickback.
Explains the pull-in reactive force and its prevention.
Explains the pushback reactive force and its prevention.
Safety precautions related to charging the battery.
Safety warnings for connecting to the power supply.
Safety guidelines for transporting the chainsaw, battery, and charger.
Safety precautions for transporting the chainsaw.
Safety precautions for transporting the battery.
Safety precautions for transporting the charger.
Safety guidelines for storing the chainsaw, battery, and charger.
Safety precautions for storing the chainsaw.
Safety precautions for storing the battery.
Safety precautions for storing the charger.
Safety warnings and general guidance for cleaning, maintenance, and repair.
Lists the steps required to prepare the saw for operation.
Instructions for mounting the charger on a wall.
Details the process and factors affecting battery charging.
How to check the battery's state of charge using LEDs.
Explains the meaning of battery LEDs for status and malfunctions.
Explains the meaning of the LED on the charger.
Instructions for mounting and removing the guide bar and saw chain.
Step-by-step guide for mounting the bar and chain.
Instructions for adjusting the tension of the saw chain.
Guidance on filling the saw chain oil tank.
How to engage the chain brake for safety.
How to disengage the chain brake for operation.
Instructions for inserting the battery into the chainsaw.
Step-by-step guide on how to start the chainsaw.
Instructions on how to properly switch off the chainsaw.
How to check the condition of the guide bar.
How to check the condition of the saw chain.
How to check the lockout button, ergo lever, and trigger.
How to verify that the chain lubrication system is working.
How to test the battery's charge and functionality.
Proper techniques for holding and controlling the chainsaw.
Instructions for performing sawing operations safely.
Techniques and safety for delimbing branches.
How to determine tree fall direction and plan escape routes.
Steps to prepare the work area before felling a tree.
Explains the basic principles of the felling cut.
Description of the plunge cutting technique for felling.
Factors to consider when choosing a felling cut.
How to fell a normal large diameter tree.
How to fell a large diameter leaning tree.
Steps to take after completing work with the chainsaw.
How to safely transport the chainsaw.
How to safely transport the charger.
Instructions for safely storing the chainsaw.
Instructions for safely storing the battery.
Instructions for safely storing the charger.
Steps for cleaning the chainsaw.
Steps for cleaning the battery.
Steps for cleaning the charger.
How to remove burrs from the guide bar.
Instructions and tips for sharpening the saw chain.
Maintenance intervals for the chain brake.
Notes on repairability of the chainsaw, battery, and charger.
Lists common faults and their remedies for the chainsaw and battery.
Lists common faults and their remedies for the charger.
Technical specifications for the MSA 60.0 C and MSA 70.0 C chainsaws.
Details chain sprocket compatibility and chain speeds.
Recommendations for using extension cords with the charger.
Specifies temperature limits for operation, charging, and storage.
Recommended temperature ranges for optimal performance.
Lists compatible guide bar and chain combinations.
Specific bar and chain combinations for the chainsaws.
Information about original STIHL spare parts and accessories.
Guidance on the proper disposal of the product and its components.
EC Declaration of Conformity for the specified chainsaw models.
UKCA Declaration of Conformity for the specified chainsaw models.
Introduction to general safety precautions for power tools.
Safety guidelines for maintaining a safe work area.
Safety precautions related to electrical hazards.
Personal safety measures and protective equipment.
Guidelines for the proper use and care of power tools.
Safety and care instructions for battery-operated tools.
Information on servicing power tools.
General safety warnings specifically for chain saws.
Explanation of kickback causes and how to prevent it.
To Next Page
General
