Stihl Msa 200 c - User Manual

Questions and Answers

D
Daniel DavidsonJul 31, 2025
Why does my Stihl Chainsaw switch off while I'm using it?
- R
  reednatashaJul 31, 2025
  If your Stihl Chainsaw switches off during operation, it could be due to a couple of reasons. The battery or the machine electronics might be overheating, in which case you should remove the battery and allow both the battery and the machine to cool off. Alternatively, there might be an electrical or electromagnetic malfunction; try removing and reinserting the battery to resolve this.
J
Jonathan DicksonAug 5, 2025
Why does my Stihl Msa 200 c have a short running time?
- J
  Jenny SmithAug 6, 2025
  Several factors can cause a Stihl Chainsaw to have a short running time. The battery may not be fully charged, so ensure you charge it completely. The battery's service life might also be reached or exceeded, requiring a check and possible replacement. Lastly, a dirty cutting attachment can reduce running time, so clean it thoroughly.
T
Taylor CarlsonAug 11, 2025
What to do if the LED on my Stihl Msa 200 c Chainsaw charger flashes red?
- P
  Paul LevyAug 11, 2025
  If the LED on your Stihl Chainsaw charger flashes red, it could indicate a few issues. First, try removing and reinserting the battery to ensure proper electrical contact between the charger and battery. If 4 LEDs on the battery flash red for about 5 seconds, remove and reinsert the battery; if the LEDs continue to flash, the battery is faulty and needs replacement. If the issue persists, the charger itself might be faulty and should be checked by a servicing dealer.
A
Anthony RileyAug 16, 2025
What to do if my Stihl Msa 200 c Chainsaw battery won't charge, even though the charger LEDs are green?
- R
  Ronald MillerAug 16, 2025
  If the battery of your Stihl Chainsaw does not charge even when the LEDs on the charger are green, it might be too hot or too cold (1 LED on the battery is red). Allow the battery to cool off or warm up gradually to temperatures between 15°C and 20°C. Make sure to operate the charger only in a closed, dry space where the ambient temperature is between +5°C and +40°C.
J
Jessica KirbyAug 20, 2025
How to fix a Stihl Chainsaw battery that gets stuck during insertion?
- J
  Jonathan AndersonAug 20, 2025
  If the battery of your Stihl Chainsaw gets stuck when you try to insert it into the machine or charger, the guides or contacts might be dirty. Carefully clean these guides and contacts to resolve the issue.
J
Julie WhiteOct 26, 2025
Why doesn't my Stihl Msa 200 c start when switched on?
- C
  Chris GarrettOct 26, 2025
  If your Stihl Chainsaw doesn't start when switched on, there might be several reasons. First, check if there is proper electrical contact between the machine and the battery by removing and reinserting the battery after visually inspecting the contacts. If the battery is discharged (1 LED flashes green), charge it. If the battery is too hot or cold (1 LED is red), allow it to cool or warm up to about 15-20°C. A battery fault (4 LEDs flash red) requires removing and reinserting the battery; if the LEDs continue to flash, replace the battery. If the unit is too hot (3 LEDs are red), let it cool off. For an electromagnetic malfunction or fault (3 LEDs flash red), try reinserting the battery; if the issue persists, the machine needs servicing. Finally, ensure there's no moisture in the machine...

Summary

Safety Precautions and Working Techniques

Clothing and Equipment

Before Starting Work

Pre-Operation Checks and Machine Startup

Ensures the tool is assembled correctly and provides steps for switching it on.

During Operation

Operational Safety and Awareness

Holding and Controlling the Unit

Proper grip and stance for safe control of the power tool.

Reactive Forces

Understanding Kickback and Pull-in

Explains dangers of kickback, pull-in, and the QuickStop chain brake.

Pushback and Kickback Reduction

Describes pushback reaction and methods to reduce kickback risk.

Cutting Operations

General Cutting Procedures and Precautions

Felling and Limbing Techniques

Felling Planning and Preparation

Felling Notches and Cuts

Felling Methods and Specialized Cuts

Maintenance and Repairs

Mounting the Bar and Chain

Removing the Chain Sprocket Cover

Mounting the Tensioning Gear

Releasing and Fitting the Saw Chain

How to release the chain brake and fit the saw chain properly.

Tensioning the Saw Chain

Retensioning During Operation

Instructions for adjusting chain tension while the tool is in use.

Checking Chain Tension

Retensioning Saw Chain if Necessary

Guidance on when and how to retension the saw chain.

Chain Lubricant

Lubricant Quality and Aging

Filling Chain Oil Tank

Opening and Filling the Oil Tank

Procedure for safely opening, filling, and closing the chain oil tank.

Checking Chain Lubrication

Ensuring Proper Chain Lubrication

How to check lubrication and warnings against operating without it.

Chain Brake

Blocking and Releasing the Chain

Methods for blocking the chain in emergencies and releasing the brake.

Checking and Servicing the Chain Brake

Connecting Charger to Power Supply

Mains Plug Insertion

Charging the Battery

Inserting the Battery into the Charger

Step-by-step guide for inserting the battery into the charger.

If Red Light Emitting Diodes Glow

Troubleshooting Red LED Indicators

Diagnosing issues indicated by red LEDs on the battery.

Light Emitting Diodes (LED) on Charger

Interpreting Charger LED Indicators

Switching On

Preparation and Battery Insertion

Steps before inserting the battery and how to insert it correctly.

Starting the Machine

Procedure for assuming stance and switching on the machine.

Switching Off

Releasing Trigger and Setting Hand Guard

How to release the trigger switch and set the hand guard to block the chain.

Operating Instructions

During Work and Chain Tension

Checking and Replacing the Chain Sprocket

Fitting a New Chain Sprocket

Maintaining and Sharpening the Saw Chain

Benefits and Risks of Chain Sharpness

Highlights the advantages of a sharp chain and risks of a dull one.

Sharpening Angles and Procedure

Checking Sharpening Angles

How to verify the correct angles for chain sharpening.

Proper Saw Chain Sharpening Steps

Step-by-step guide for performing saw chain sharpening.

Depth Gauge Setting

Setting and Lowering Depth Gauges

Procedures for setting and adjusting the depth gauges on the saw chain.

Maintenance and Care Schedule

Machine Component Maintenance

Minimize Wear and Avoid Damage

Importance of Regular Maintenance Work

Main Parts Identification

Chainsaw Components

Cutting Attachment Specifications

Ordering Spare Parts

Troubleshooting Guide

Machine Does Not Start or Switches Off

Solutions for power tool startup failures and unexpected shutdowns.

Battery and Charging Issues

General Power Tool Safety Warnings

Work Area, Electrical, and Personal Safety

Attire, Dust Control, Tool & Battery Care

Safe Operation, Handling, and Kickback Prevention

Stihl Msa 200 c Specifications

General

Battery Type	Lithium-Ion
Voltage	36 V
Power Source	Battery
Chain Gauge	0.043 in (1.1 mm)
Chain Pitch	1/4 inch
Vibration Level (Front Handle)	2.5 m/s^2
Bar Length	12-14 in. (30-35 cm)