Summa SummaSign T750 - User Manual

Service Manual
SummaSign Series
Summa NV
Rochesterlaan 6
8470 Gistel
Belgium

Summary

SECTION 1 Keyboard Control

1.1. The Control Panel

Details the functions of the liquid crystal display (LCD) and control panel keys.

1.2. Normal Operation

Explains on-line, off-line, and local operation modes for cutting and plotting.

1.3. The User Config Menu

Allows configuration of cutter operating parameters and saving user settings.

1.4. System Set Up

Covers system setup parameters like concatenation, smoothing, and emulation.

1.5. Internal Test Menu

1.6. System Tests

SECTION 2 Replacement Guidelines

2.1. Removing the Left-Hand Cover

2.2. Removing the Right-Hand Cover

2.3. Removing the Bottom Plate

2.4. Replacing the Camrollers

2.5. Replacing the X-Motor in the 500, 610 and the Old 750

2.6. Replacing an X-Motor in the Models 750;1010 and 1300

2.7. Replacing the Y-Motor

2.8. Replacing the LCD or the Keyboard

2.9. Replacing the Main PCB

2.10. Replacing the Small PCB on the Main PCB

2.11. Replacing a Drag Head or a Tangential Head

2.12. Replacing the Flat Cable for the Head

2.13. Replacing the Y-Belt

2.14. Replacing the Cutting Strip

2.15. Replacing the Sensors

2.16. Replacing the Fan Motor

2.17. Replacing the Drive Drum

SECTION 3 Maintenance

3.1. Cleaning the Drive System

3.2. Cleaning the Sensors

3.3. Cleaning the Nose Piece

3.4. Operating Voltage Conversion

SECTION 4 Calibration

4.1. Machine Type

4.2. Media Calibration

4.3. Head Calibration

4.5. OPOS Calibration (Optional)

4.6. Sensor Tests

SECTION 5 Error Codes - Troubleshooting

5.1. Motor Hot

Troubleshooting steps for the 'MOTOR HOT' error message.

5.2. Error in X-Axis

Troubleshooting steps for errors related to the X-axis movement.

5.3. Error in Y-Axis Position

Troubleshooting steps for errors related to Y-axis positioning.

5.4. Low Line Voltage

Troubleshooting steps for low input voltage errors.

5.5. High Line Voltage

Troubleshooting steps for high input voltage errors.

5.6. Illegal Plot Command

Troubleshooting steps for illegal plot commands in DM/PL.

5.7. Illegal Clip & Scale Settings

Troubleshooting steps for illegal clip/scale settings in DM/PL.

5.8. Syntax Error

Troubleshooting steps for syntax errors, often related to HPGL commands.

5.9. NVRAM Failures and Messages

Troubleshooting steps for NVRAM failures and related messages.

5.10. RS232 Error

Troubleshooting steps for errors occurring during RS232 communication.

5.11. Internal Errors

Troubleshooting steps for internal firmware or board errors.

5.12. Flashing Errors and Messages (Only on New Type of PCB)

Troubleshooting steps for flashing errors on newer PCB types.

5.13. ROM Error

Troubleshooting steps for ROM errors, indicating potential ROM failure.

5.14. RAM Error

Troubleshooting steps for RAM errors, indicating potential RAM failure.

5.15. Machine Unable to Find the Knife Home Position

Troubleshooting steps when the machine cannot find the knife's home position.

5.16. Markers Not Sensed Properly

Troubleshooting steps when the machine fails to sense markers.

Summa SummaSign T750 Specifications

General

Cutting Width	750 mm
Contour Cutting	Standard
Repeatability	0.1 mm (0.004 in.)
Software Compatibility	Adobe Illustrator, CorelDRAW
Power Requirements	100-240 V, 50-60 Hz