Supermicro C7Z270-CG - Connecting Cables; ATX Main PWR & CPU PWR Connectors (JPW1 & JPW2)

Chapter 2: Installation
2-21
JPCIE1
JPCIE3
JPCIE6
MH12
MH10
MH11
MH13
MH14
S12
S4
MH15
MH18
JUSBA
JAUDIO1
JPCIE4
JPCIE5
JPCIE2
JUSBC
MH9
MH4
MH2
MH5
MH7
MH8
JUSBLAN1
B1
+
JBT1
10
9
2
SP1
JP2
JD1
1
2
15
16
3
1
JSD1
1
5
6
9
FAN5
FAN1
FAN4
FAN2
FAN3
S8
JTPM1
1
2
1920
JPW1
LED20
A
C
LED17
A
C
LED19
A C
LED18
A C
LED3
LED2
A
C
A
LED1
JPW2
1
JL2
JI2C2
JI2C1
1
JSPDIF_OUT
JL1
LED4
JBR1
JLED1
1
JPAC1
1
JPL1
JWD1
JPME2
DESIGNED IN USA
C7Z270-CG
REV:1.00
BIOS LICENSE
MAC CODE
BAR CODE
CLEAR CMOS
RESET BUTTON
POWER BUTTON
U.2 CONNECTOR 2
U.2 CONNECTOR 1
I-SATA5
I-SATA4
I-SATA3
SYS_FAN2
SYS_FAN1
CPU_FAN2
SYS_FAN3
I-SATA1
USB 10/11 (3.1)
USB6/7
LAN
DVI
PCIE M.2 CONNECTOR 1
USB2/3
USB4/5
USB 8/9 (3.1)
X
PWR
HDD
LED LED
NIC
1
OH/FF X
RST
PWR
ON
PCIE M.2 CONNECTOR 2
ON:BIOS RECOVERY
OFF:NORMAL
JBR1
TPM/PORT80
INTRUSION
CHASSIS
JL1:
KB/MOUSE
USB 0/1
USB 12/13 (3.0)
I-SATA0
DIMMB2
DIMMB1
DIMMA2
DIMMA1
HDMI/DP
CPU SLOT1 PCI-E 3.0 X4 (IN X16)
PCH SLOT2 PCI-E 3.0 X1
CPU SLOT3 PCI-E 3.0 X8 (IN X16)
PCH SLOT4 PCI-E 3.0 X1
PCH SLOT5 PCI-E 3.0 X1
CPU SLOT6 PCI-E 3.0 X16
5V STBY POWER
JSTBY1:
JWD1:
JSD1:
2-3:DISABLE
1-2:ENABLE
JPL1:LAN
2-3:NMI
1-2:RST
WATCH DOG
2-3:ME MANUFACTURING MODE
CPU_FAN1
1-2:NORMAL
JPME2:
SATA DOM PWR
JTPM1:
JLED1:
3 PIN POWER LED
AUDIO FP
JBT1
CMOS CLEAR
SPEAKER:1-4
JD1:
BUZZER:3-4
JI2C1/JI2C2
ON :ENABLE
OFF:DISABLE
HD AUDIO
JF1
COM1
2-3:DISABLE
1-2:ENABLE
JPAC1:AUDIO
I-SATA2
2-7 Connecting Cables
This section provides brief descriptions and pin-out denitions for on-
board headers and connectors. Be sure to use the correct cable for each
header or connector.
A. 24-Pin ATX Main PWR
B. 8-Pin PWR
ATX Power 24-pin Connector
Pin Denitions (JPW1)
Pin# Denition Pin # Denition
13 +3.3V 1 +3.3V
14 -12V 2 +3.3V
15 COM 3 COM
16 PS_ON 4 +5V
17 COM 5 COM
18 COM 6 +5V
19 COM 7 COM
20 Res (NC) 8 PWR_OK
21 +5V 9 5VSB
22 +5V 10 +12V
23 +5V 11 +12V
24 COM 12 +3.3V
(Required)
12V 8-pin Power Connec-
tor Pin Denitions
Pins Denition
1 through 4 Ground
5 through 8 +12V
ATX Main PWR & CPU PWR
Connectors (JPW1 & JPW2)
The 24-pin main power connector (JPW1)
is used to provide power to the moth-
erboard. The 8-pin CPU PWR connector
(JPW2) is also required for the processor.
These power connectors meet the SSI
EPS 12V specication. See the table on
the right for pin denitions.
A
B