0-6
Operation .........................................3-1
Before starting operation .........................3-2
Getting on or off the machine ...............3-2
Walk-around inspection ....................... 3-2
Daily inspection .................................... 3-2
Starting and stopping the engine ............. 3-3
Before starting the engine .................... 3-3
Starting the Engine .............................. 3-4
Warming up the engine ........................ 3-5
Stopping the engine ............................ 3-5
Operating the machine ............................ 3-6
Lever pattern (ISO pattern) ................... 3-6
Warming up the machine
(hydraulic oil)
........................................ 3-8
Inspection after warm-up ................... 3-10
Traveling the machine ........................ 3-11
Stopping travel .................................. 3-15
Operating the working equipment ...... 3-16
Operating procedures ............................ 3-19
Prohibited operations .........................3-19
Precautions for operation ...................3-22
Precautions when traveling on slopes 3-23
Getting out of mud ............................ 3-25
Operations possible with this
machine............................................. 3-26
Parking the machine
.............................. 3-27
Parking .............................................. 3-27
Inspection and checks after stopping
the engine.......................................... 3-28
Handling in cold climates
....................... 3-29
Preparing for cold climates ................3-29
Cautions after operations ................... 3-29
After the cold climate ......................... 3-29
Handling tires ........................................3-30
Prohibitions ........................................3-30
Precautions .......................................3-31
Transport .........................................4-1
Loading and unloading ............................ 4-2
Hoisting the machine ............................... 4-4
Securing the machine .............................. 4-6
Transporting posture ............................4-6
Precautions to be taken during
transportation .......................................... 4-7
Maintenance ....................................5-1
General .................................................... 5-2
Maintenance overview ......................... 5-2
Cautions on maintenance .................... 5-2
Service data ............................................ 5-4
Fuel and lubricant table ........................ 5-4
Regularly replace the hydraulic oil ........5-8
List of consumables ............................. 5-9
List of tools (If equipped) .................... 5-10
List of tightening torques ...................5-11
Safety-critical parts ................................ 5-12
Maintenance list ..................................... 5-14
Walk-around inspection ......................... 5-18
Inspecting by opening the engine
hood and covers................................ 5-18
Inspecting by walking around the
machine
............................................. 5-19
Inspecting while sitting in the operator’s
seat
................................................... 5-19
Daily inspection (every 10 hours) ............ 5-20
Inspecting and replenishing the
coolant
.............................................. 5-20
Inspecting and replenishing the
engine oil
........................................... 5-21
Cleaning the dust screen ...................5-22
Inspecting the water separator and
the fuel filters
..................................... 5-22
Inspecting the fuel level ...................... 5-23
Inspecting the hydraulic oil tank level
and replenishing
................................ 5-24
Lubricating the working equipment .... 5-25
Inspecting and inflating the tires ......... 5-26
Checking the wheel nut torques .........5-27
After the initial 50 hours
(only for new machines)
......................... 5-28
Replacing the engine oil and the oil
filter
................................................... 5-28
Inspecting and adjusting the V-belt .... 5-30
Inspecting and adjusting the
compressor belt (AC)
......................... 5-32
Replacing the hydraulic oil return filter 5-33
Replacing the pilot line filter ................ 5-34
Every 50 hours ..................................... 5-35
Draining the water from the fuel tank ..5-35
Inspecting the battery fluid level and
replenishing .......................................5-36
After the initial 250 hours
(only for new machines)
......................... 5-38
Replacing the slew motor gear oil ...... 5-38
Every 250 hours ................................... 5-39
Inspecting and adjusting the V-belt .... 5-39
Inspecting and adjusting the
compressor belt (AC)
........................ 5-39
Lubricating the undercarriage ............5-40