BIKERACE: Service & Maintenance Manual - rev. 1.1
Page ii
7.8. DISASSEMBLING THE ALTERNATOR................................................................................................................. 7.10
7.9. DISASSEMBLING THE BELT.............................................................................................................................. 7.11
7.10. DISASSEMBLING THE CHAIN............................................................................................................................7.13
7.11. DISASSEMBLING THE PULLEY..........................................................................................................................7.14
7.12. DISASSEMBLING THE PEDAL CRANK GROUP.................................................................................................... 7.15
7.13. DISASSEMBLING THE ALTERNATOR BRUSHES ................................................................................................. 7.16
8. ADJUSTMENTS....................................................................................................................................................8.1
8.1. ALIGNING THE BELT.......................................................................................................................................... 8.1
8.2. BELT TENSION .................................................................................................................................................. 8.2
8.3. CHAIN ALIGNMENT ........................................................................................................................................... 8.3
8.4. CHAIN TENSION ................................................................................................................................................ 8.5
8.5. PLAY OF SADDLE STEM .....................................................................................................................................8.6
8.6. WEAR OF ALTERNATOR BRUSHES .....................................................................................................................8.7
8.7. PLAY OF THE PEDAL GROUP .............................................................................................................................. 8.8
8.8. ADJUSTING THE LCD BACKLIGHTING...............................................................................................................8.9
8.9. ADJUSTING THE BUZZER TONE........................................................................................................................8.10
9. CONFIGURING THE MACHINE ......................................................................................................................9.1
9.1. MACHINE HW CONFIGURATION ....................................................................................................................... 9.1
9.1.1. Machine No. configuration ............................................................................................................... 9.1
9.1.2. Alternator configuration ................................................................................................................... 9.1
10. SCHEDULED MAINTENANCE .......................................................................................................................10.1
10.1. EXTERNAL CLEANING OPERATIONS.................................................................................................................10.1
10.1.1. Setting up the operation ..................................................................................................................10.1
10.1.2. Cleaning operations ........................................................................................................................ 10.1
10.2. INTERNAL CLEANING OPERATIONS.................................................................................................................. 10.2
10.2.1. Setting up the operation ..................................................................................................................10.2
10.2.2. Cleaning operations ........................................................................................................................ 10.2
10.3. SPECIAL MAINTENANCE OPERATIONS..............................................................................................................10.3
10.3.1. Setting up the operation ..................................................................................................................10.3
10.3.2. Checking the working conditions ....................................................................................................10.3
10.3.3. Checking the wiring and connections.............................................................................................. 10.3
10.3.4. Checking the display........................................................................................................................ 10.3
10.3.5. Checking the wear of the rubber handlebar cover .......................................................................... 10.3
10.3.6. Checking the state of wear of the chain........................................................................................... 10.4
10.3.7. Lubrication......................................................................................................................................10.4
10.3.8. Checking the state of wear of the alternator belt............................................................................. 10.4
10.3.9. Checking the play of the saddle stem............................................................................................... 10.4
10.3.10. Checking the operation of the cardio receiver ................................................................................ 10.4
10.3.11. Checking the resistance setting ....................................................................................................... 10.4
10.3.12. Checking the noise of the brushes ................................................................................................... 10.4
11. APPENDIX...........................................................................................................................................................11.1
11.1. TECHNICAL NOTES ON CARDIO RECEIVERS ..................................................................................................... 11.1
11.1.1. Type of ASIC.................................................................................................................................... 11.2
11.1.2. Presence of electromagnetic fields..................................................................................................11.2
11.1.3. Reducing receiver sensitivity...........................................................................................................11.3
11.1.4. Mechanical vibrations..................................................................................................................... 11.4
11.1.5. Position of the receiver.................................................................................................................... 11.4
11.1.6. Routing of cables............................................................................................................................. 11.5
11.2. PERSONAL CODED DEVICE............................................................................................................................. 11.6
11.2.1. Operating modes ............................................................................................................................. 11.6
11.2.2. Upgrade of machines already installed........................................................................................... 11.7
11.3. SPECIAL FUNCTIONS ....................................................................................................................................... 11.8
11.3.1. Displaying the selected type of alternator....................................................................................... 11.8
To Next Page
Loading...