EasyManua.ls Logo

TECO F510 series - Page 41

TECO F510 series
100 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Loading...
40
Group 17: IM Motor Automatic Tuning
Parameters
Code
Parameter
Name
Setting Range Default
Attribu
te
17-00
Mode
Selection of
Automatic
Tuning
0: Rotational
Auto-tuning
VF:2
SLV:6
1: Static Auto-
tuning
2: Stator
Resistance
Measurement
3: Reserved
4: Loop Tuning
5: Rotational
Auto-tuning
Combination
(Item: 4+2+0)
Note
6: Static Auto-
tuning
Combination
(Item: 4+2+1)
Note
17-01
Motor Rated
Output
Power
0.00~600.00 -
17-02
Motor Rated
Current
0.1~1200.0 -
17-03
Motor Rated
Voltage
200V: 50.0~240.0
-
400V:100.0~480.0
-
17-04
Motor Rated
Frequency
4.8~400.0 60.0
17-05
Motor Rated
Speed
0~24000 KVA
*a
17-06
Pole
Number of
Motor
2~16 (Even) 4 *6
17-07 Reserved
17-08
Motor No-
load Voltage
200V: 50~240
KVA
*a
400V: 100~480
17-09
Motor
Excitation
Current
0.01~600.00
(15%~70%
motor rated
current)
KVA
*a
1
17-10
Automatic
Tuning Start
0: Disable
0
1: Enable
17-11
Error
History of
Automatic
Tuning
0: No Error
0
1: Motor Data
Error
2: Stator
Resistance
Tuning Error
3: Leakage
Induction
Tuning Error
4: Rotor
Resistance
Tuning Error
5: Mutual
Induction
Tuning Error
6: Reserved
Group 17: IM Motor Automatic Tuning
Parameters
Code
Parameter
Name
Setting Range Default
Attribu
te
7: DT Error
8: Motor
Acceleration
Error
9: Warning
17-12
Leakage
Inductance
Ratio
0.1 ~ 15.0 3.4
17-13
Slip
Frequency
0.10 ~ 20.00 1.00
17-14
Rotational
Tuning
Mode
Selection
0: VF Mode
1: Vector Mode
0
Note1
*a: KVA means the default value of this
parameter will be changed by different
capacities of inverter.
1: It can be set when 17-00=1, 2, 6.
Group 18: Slip Compensation
Parameters
Code
Parameter
Name
Setting Range Default
Attribu
te
18-00
Slip
Compensati
on Gain at
Low Speed
0.00~2.50 0.00
*d
*1
18-01
Slip
Compensati
on Gain at
High Speed
-1.00~1.00 0.0 *1
18-02
Slip
Compensati
on Limit
0~250 200
18-03
Slip
Compensati
on Filter
Time
0.0~10.0 1.0
18-04
Regenerativ
e Slip
Compensati
on Selection
0: Disable
0
1: Enable
18-05
FOC Delay
Time
1~1000 100
18-06 FOC Gain 0.00~2.00 0.1
*d: Default value is 0.00 in V/F mode while it is
1.0 in SLV mode.
Group 19 Reserved

Other manuals for TECO F510 series

Related product manuals