Assemble Seat Back
Figure 20: Locate the Step 10 Hardware Kit.
Insert the Seat Back Assembly onto the housing
behind the Lower Seat and hand tighten
4 × Bolts and 4 × Washers.
Proceed to fully tighten all the Bolts with the
6 mm Allen Wrench.
STEP 10
STEP 11
12
Figure 20
Figure 21
Assemble Seat Pivot Cover Set
Figure 21: Locate the Seat Pivot Cover Set,
noting Right and Left Markings.
Use the Step 11 Hardware Kit to attach the Seat
Pivot Cover Set behind the Lower Seat.
With the Phillips Screwdriver fully tighten
2 × Phillips Screws and 2 × Phillips Bolts.
STEP 20 - INSTALL THE SEAT BACK WITH FOUR
(4) M8X15 BOLTS AND WASHERS BY HAND.
AFTER THE BOLTS HAVE BEEN STARTED BY
HAND, PROCEED TO FULLY TIGHTENING ALL
FOUR (4) BOLTS WITH THE 6MM ALLEN.
USE HK2071.
8
A
1234567
D
C
B
C
A
D
B
5 3 16 248 7
8
A
1234567
D
C
B
C
A
D
B
5 3 16 248 7
AI DRAWINGS
SHEET 21 OF 40
REV
PROJECT:
DRAWN
UNLESS OTHERWISE NOTED
SURFACE ROUGHNESS PER ANSI B46.1
DIMENSIONING PER ASME Y14.5-2009
WELD SYMBOLS PER AWS A2.4
FINISH:
UOS 63RMS ON
MACHINED
SURFACES OR
AS PROCURED
.X
.XX
.XXX
ANGLE
EXPECTATIONS PROPRIETARY
THE INFORMATION CONTAINED HEREIN
IS PROPRIETARY TO EXPECTATIONS AND
SHALL NOT BE REPRODUCED IN WHOLE
OR IN PART OR USED FOR ANY PURPOSE
EXCEPT WHEN SUCH USER POSSESSES
DIRECT WRITTEN AUTHORIZATION
FROM EXPECTATIONS LLC
SCALE: NONE
SIZE:
D
A
TOLERANCES
UNLESS NOTED
=
.1
=
.03
=
.005
=
1
NICK SOLLER
FILLET RADII: .005-.010
CORNER BREAK: .005-.010
ALL DIMENSIONS IN INCHES
EXPECTATIONS LLC
BONNEY LAKE, WA 98391
DRAWING
LT7
STEP 21 - INSTALL THE BACKREST JOINT
COVER WITH TWO (2) PHILLIPS SCREWS
AND TWO (2) M4X15 PHILLIPS BOLTS USING
THE PHILLIPS SCREW DRIVER.
USE HK2072.
8
A
1234567
D
C
B
C
A
D
B
5 3 16 248 7
8
A
1234567
D
C
B
C
A
D
B
5 3 16 248 7
AI DRAWINGS
SHEET 22 OF 40
REV
PROJECT:
DRAWN
UNLESS OTHERWISE NOTED
SURFACE ROUGHNESS PER ANSI B46.1
DIMENSIONING PER ASME Y14.5-2009
WELD SYMBOLS PER AWS A2.4
FINISH:
UOS 63RMS ON
MACHINED
SURFACES OR
AS PROCURED
.X
.XX
.XXX
ANGLE
EXPECTATIONS PROPRIETARY
THE INFORMATION CONTAINED HEREIN
IS PROPRIETARY TO EXPECTATIONS AND
SHALL NOT BE REPRODUCED IN WHOLE
OR IN PART OR USED FOR ANY PURPOSE
EXCEPT WHEN SUCH USER POSSESSES
DIRECT WRITTEN AUTHORIZATION
FROM EXPECTATIONS LLC
SCALE: NONE
SIZE:
D
A
TOLERANCES
UNLESS NOTED
=
.1
=
.03
=
.005
=
1
NICK SOLLER
FILLET RADII: .005-.010
CORNER BREAK: .005-.010
ALL DIMENSIONS IN INCHES
EXPECTATIONS LLC
BONNEY LAKE, WA 98391
DRAWING
LT7
BOLT
BOLT
SCREW
SCREW
Step 10 Hardware
Step 11 Hardware
To Next Page
Loading...
