Tektronix TDS 420A - Page 226

Index
Index–10
TDS 420A, TDS 430A, TDS 460A & TDS 510A User Manual
RLE Color, Hardcopy menu, 3–48
RMS, 3–75
Roll, Glossary–3
Roll Mode, 3–99
Triggered, 3–99
Triggered, with Single Sequence, 3–99
Untriggered, 3–99
Untriggered, with Single Sequence, 3–99
Using, 3–99
RS-232, Port (optional), 3–97
RUN/STOP, Acquire menu, 3–9
Runt trigger, 3–91, 3–94
Runt, Main Trigger menu, 3–94
S
Sample acquisition mode, 3–5
Sample interval, Glossary–3
Sample, Acquire menu, 3–8
Sampling, Glossary–3
Save, Setups, 3–103
Save Current Setup, Save/Recall Setup menu, 3–103
Save Format, Save/Recall Waveform menu, 3–107
Save Waveform, Save/Recall Waveform menu, 3–105
Save/Recall SETUP button, 3–43, 3–103
Save/recall SETUP button, 2–12
Save/Recall Setup menu, 3–103
factory status, 3–103
Recall Factory Setup, 3–104, 3–113
Recall Saved Setup, 3–103
Save Current Setup, 3–103
user status, 3–103
Save/Recall WAVEFORM button, 3–43, 3–105
Save/Recall Waveform menu, 3–105
active status, 3–105
Delete Refs, 3–106
empty status, 3–105
Ref1, Ref2, Ref3, Ref4, 3–106
Save Format, 3–107
Save Waveform, 3–105
Saving and recalling setups, 3–103
Saving and recalling waveforms, 3–105
Scale, vertical, 3–34, 3–133, 3–138
Scan Parameter, Video Trigger menu, 3–129
SECAM Video Standard, 3–128
SECAM, Video Trigger menu, 3–128
seconds, Cursor menu, 3–120
SELECT button, 3–120
Select Measrmnt, Measure menu, 3–76, 3–79
Selected waveform, 3–111
Selecting channels, 3–111
Self test, 1–5
Service Assurance, A–5
Set 1st Source to, More menu, 3–140
Set 2nd Source to, More menu, 3–140
Set Function to, More menu, 3–139
SET LEVEL TO 50% button, 3–25
Set Levels in % units, Measure menu, 3–78
Set operator to, More menu, 3–140
Set Single Source to, More menu, 3–139
Set Thresholds, Main Trigger menu, 3–69
Set to 10%, Horizontal menu, 3–59
Set to 50%, Horizontal menu, 3–59
Set to 50%, Main Trigger menu, 3–24, 3–25
Set to 90%, Horizontal menu, 3–59
Set to ECL, Main Trigger menu, 3–24
Set to TTL, Main Trigger menu, 3–24
Set to Zero, Vertical menu, 3–125
Setting Up for the Examples, 2–11
Setup menu, 2–12
Setups, Save and recall, 3–103
Shipping, B–1
side menu, 2–7
Side menu buttons, 2–3
SIGNAL OUTPUT, BNC, 2–6
Signal Path Compensation, 1–5–1–6, 3–115
Sin(x)/x interpolation, 3–19, Glossary–2
Sin(x)/x interpolation, Display menu, 3–19
Single Acquisition Sequence, Acquire menu, 3–10
SINGLE TRIG button, 3–10, 3–25, 3–26
Single Wfm Math, More menu, 3–139
Slope, 3–21
Slope, Delayed Trigger menu, 3–14
Slope, Main Trigger menu, 3–24
Snapshot, Readout, 3–81
Snapshot of Measurements, 2–25, 3–81
Snapshot, Measure menu, 3–81
Software, 1–1
Software version, 3–15
Source, Delayed Trigger menu, 3–13
Source, Main Trigger menu, 3–23, 3–93, 3–94
Source, Video Trigger menu, 3–128
Spooler, Hardcopy, 3–50
Start up, 1–3
State trigger, 3–72
State, Main Trigger menu, 3–69, 3–72
STATUS button, 3–15
Status menu, 3–15–3–16
Display, 3–15
Firmware version, 3–15
I/O, 3–15
System, 3–15
Trigger, 3–15
Waveforms, 3–15