Tektronix TDS 420A - Page 7

Table of Contents
iv
TDS Family Oscilloscope Programmer Manual
List of Tables
Table 2–1: BNF Symbols and Meanings 2–1. . . . . . . . . . . . . . . . . . . . . . . .
Table 2–2: Command Message Elements 2–2. . . . . . . . . . . . . . . . . . . . . . .
Table 2–3: Comparison of Header Off and On Responses 2–3. . . . . . . . .
Table 2–4: Acquisition Commands 2–13. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table 2–5: Alias Commands 2–14. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table 2–6: Application Menu Commands 2–14. . . . . . . . . . . . . . . . . . . . . .
Table 2–7: Calibration and Diagnostic Commands 2–15. . . . . . . . . . . . . .
Table 2–8: Cursor Commands 2–15. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table 2–9: Display Commands 2–16. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table 2–10: File System Commands 2–18. . . . . . . . . . . . . . . . . . . . . . . . . . .
Table 2–11: Hardcopy Commands 2–19. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table 2–12: Histogram Commands 2–19. . . . . . . . . . . . . . . . . . . . . . . . . . .
Table 2–13: Horizontal Commands 2–20. . . . . . . . . . . . . . . . . . . . . . . . . . .
Table 2–14: Limit Test Commands 2–22. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table 2–15: Mask Commands 2–23. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table 2–16: Measurement Commands 2–24. . . . . . . . . . . . . . . . . . . . . . . . .
Table 2–17: Miscellaneous Commands 2–26. . . . . . . . . . . . . . . . . . . . . . . . .
Table 2–18: RS-232 Commands 2–27. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table 2–19: Save and Recall Commands 2–28. . . . . . . . . . . . . . . . . . . . . . .
Table 2–20: Status and Error Commands 2–29. . . . . . . . . . . . . . . . . . . . . .
Table 2–21: Trigger Commands 2–30. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table 2–22: Vertical Commands 2–37. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table 2–23: Extended-Acquisition-Length Mode Channels and Record
Lengths 2–42. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table 2–24: Waveform Commands 2–43. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table 2–25: Zoom Commands 2–45. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table 2–26: Waveform Data Points Supported for Reference
Locations 2–63. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table 2–27: Commands that Affect BUSY? Response 2–69. . . . . . . . . . . .
Table 2–28: Offset Ranges for the TDS 400A, 510A, 540C, 600B, 754C, &
784C (All Channels) and the TDS 520C & 724C
(Channel 1 & Channel 2) using a 1x Probe 2–74. . . . . . . . . . . . . . . . . .
Table 2–29: Offset Ranges for the TDS 520C & 724C (Aux 1 & Aux 2)
using a 1x Probe 2–74. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table 2–30: DATa and WFMPre Parameter Settings 2–101. . . . . . . . . . . . .