Teledyne Linea - User Manual

90 pages

Save Page as PDF

To Next Page

03-032-20206-00

www.teledynedalsa.com

Linea

Camera User’s Manual

2k and 4k Monochrome CMOS Line Scan

Main Page

Table of Contents3
System Precautions and Cleaning6
- Precautions6
- Electrostatic Discharge and the CMOS Sensor6
The Linea Camera7
Camera Highlights7
Camera Performance Specifications8
Certifications and Compliance9
Supported Industry Standards9
Responsivity10
Mechanicals11
Quick, Simple Steps to Acquire an Image12
Software and Hardware Setup13
- Recommended System Requirements13
Setup Steps: Overview13
- Install and Configure Frame Grabber and Software13
- Connect Camera Link and Power Cables13
- Establish Communicating with the Camera13
- Operate the Camera13
Step 1. Install and Configure the Frame Grabber and Software14
- Install Frame Grabber14
- Install Sapera LT and Camexpert GUI14
Step 2. Connect Data, Trigger, and Power Cables15
- Data Connector: Camera Link16
- Camera Link Bit Definitions18
- Camera Link Drive Capability19
- Input Signals, Camera Link19
- Output Signals, Camera Link Clocking Signals19
- Power Connector20
- Pocl Power over Camera Link20
- Leds21
Step 3. Establish Communication with the Camera21
- Power on the Camera21
- Connect to the Frame Grabber21
- Connect to the Camera21
- Check LED Status22
- Software Interface22
Using Sapera Camexpert with Linea Cameras23
- Camexpert Panes24
Camera Operation26
Factory Settings26
Check Camera and Sensor Information26
Saving and Restoring Camera Settings27
Verify Temperature and Voltage27
Camera Link Configuration29
Trigger Modes29
Exposure Controls29
Exposure Modes in Detail30
Set Line Rate33
Set Exposure Time36
Control Gain and Black Level36
Set Image Size37
Set Baud Rate37
Pixel Format38
Pixel Readout Direction (Mirroring Mode)38
Resetting the Camera38
Calibrating the Camera39
Contrast Enhancement42
Appendix A: Genicam Commands43
Camera Information Category43
- Camera Information Feature Descriptions44
- Camera Configuration Selection Dialog47
- Camera Power-Up Configuration47
- User Set Configuration Management47
Camera Control Category48
- Camera Control Feature Descriptions49
- Digital I/O Control Feature Descriptions50
Flat Field Category51
- Flat Field Control Feature Description52
- Region of Interest (ROI)53
Image Format Control Category53
- Image Format Control Feature Description54
Binning55
Area of Interest (AOI) Setup56
Transport Layer Control Category58
- Transport Layer Feature Descriptions59
Acquisition and Transfer Control Category59
- Acquisition and Transfer Control Feature Descriptions60
Serial Port Control Category61
- Serial Port Control Feature Descriptions61
File Access Control Category62
- File Access Control Feature Descriptions63
- File Access Via the Camexpert Tool64
- Download a List of Camera Parameters65
Appendix B: ASCII Commands67
- Port Configuration68
- Disabling the Esc Key for Direct Access to ASCII Commands69
- Commands69
Appendix C: Error and Warning Messages78
Appendix D: Quick Setup and Image Acquisition80
Appendix E: the Sensor Window83
Cleaning and Protecting against Dust, Oil, and Scratches83
Cleaning the Sensor Window84
Appendix F: Camera, Frame Grabber Communication85
Setting up Communication between the Camera and the Frame Grabber85
EMC Declaration of Conformity87
Revision History88
Index89

Need help?

Do you have a question about the Teledyne Linea and is the answer not in the manual?

Teledyne Linea Specifications

General

Brand	Teledyne
Model	Linea
Category	IP Camera
Language	English

Related product manuals

Teledyne BOA Pro

27 pages

Teledyne Linea - User Manual

Table of Contents

Teledyne Linea Specifications

Related product manuals