Why is my Tennant M30 Scrubber's scrubbing performance poor?
If your Tennant Scrubber's scrubbing performance is not up to par, consider the following: * Ensure the 1?STEP Scrub button is turned on. * The solution tank might be empty; fill it. * Debris could be caught on the main brushes; remove it.
Why is my Tennant M30 having poor sweeping performance?
If you're experiencing poor sweeping performance with your Tennant Scrubber, several factors could be responsible. Check the brush bristles for wear and replace the brushes if needed. Ensure the brush pressure isn't set too light; increase it if necessary. Verify that the main brushes are properly adjusted. Debris caught in the main brush drive mechanism can also hinder performance, so remove any obstructions. If the main and/or side brush drive has failed, or if you are using improper main brushes, it is recommended to call a Tennant service representative. Additionally, check if the hopper is full and empty it if necessary. Finally, inspect the hopper lip skirts for wear or damage and replace them if needed.
What to do if my Tennant M30 Scrubber vacuum fan will not turn on?
If the vacuum fan on your Tennant Scrubber isn't turning on, check the following: * Ensure the vacuum fan/squeegee button is turned on. * The recovery tank might be full; drain it. * Foam may be filling the recovery tank; empty it and use less detergent or a defoamer. * The recovery tank sensor could be dirty or stuck; clean or replace the sensor.
How do I stop excessive dusting from my Tennant Floor Machine?
To address excessive dusting with your Tennant Floor Machine: * Replace or adjust brush skirts and/or brush seals if they are worn, damaged, or out of adjustment. * Shake and/or replace the dust filter if the hopper dust filter is clogged. * Replace the vacuum fan seal if the sweep vacuum fan seal is damaged. * Allow the Thermo?Sentry to cool if it has tripped.
Why is the FaST System not working on my Tennant M30 Scrubber?
If the FaST system on your Tennant Scrubber isn't operating, check these potential causes: * Ensure the FaST button is turned on. * The FaST?PAK supply hose and/or connector might be clogged; soak the connector and hose in warm water and clean them. * The FaST?PAK carton could be empty or not connected; replace the FaST?PAK carton and/or connect the supply hose. * The FaST system might not be primed; operate the FaST solution system for a few minutes to prime it. * The filter screen could be clogged; drain the solution tank, remove, and clean the filter screen.
What to do if ES System does not operate on Tennant Floor Machine?
If the ES System on your Tennant Floor Machine isn't operating, first ensure the ES button is turned on. If the ES sensor in the tank is dirty, clean it. A clogged ES pump filter should be cleaned. If the water level in the recovery tank is too low, fill it about half full. Also, ensure the water level in the solution tank isn't too low and fill it if necessary.
Why won't the scrub vacuum fan turn on in my Tennant Floor Machine?
If the scrub vacuum fan on your Tennant Floor Machine won't turn on, there are a few things to check: * Make sure the vacuum fan/squeegee button is turned on. * Drain the recovery tank if it is full. * Empty the recovery tank if it is filling with foam; use less detergent or a defoamer to prevent foaming. * Clean or replace the recovery tank sensor if it is dirty or stuck.
How to fix trailing water or poor water pickup on Tennant Scrubber?
If you notice trailing water or poor water pickup with your Tennant Scrubber, there are several potential causes. First, ensure the scrub vacuum fan is turned on. If it is, check the squeegee blades for wear and rotate or replace them if necessary. Also, verify the squeegee is properly adjusted. Other possible causes include a clogged vacuum hose or a dirty vacuum screen, which can be resolved by flushing the hose or cleaning the screen. Additionally, ensure there is detergent in the solution tank to prevent squeegee chatter. Check the recovery tank cover seals for wear and replace if needed. Remove any debris caught in the squeegee, and ensure the vacuum hose is properly connected and not damaged. Finally, confirm the recovery tank cover is completely closed and free of obstructions.
What to do if sweeping or scrubbing functions don't turn on in my Tennant Floor Machine?
If the sweeping or scrubbing functions on your Tennant Floor Machine do not turn on, check the following: * Ensure the hopper is completely lowered. * If there is a fire in the hopper, shut off the machine, extinguish the fire, and call emergency personnel if needed. * If the recovery tank is full, press the scrub vacuum fan/squeegee button for one minute of extended water pickup, then empty the recovery tank. For ES models, activate the ES system to prevent this.
How to improve sweeping performance of Tennant M30?
To improve the sweeping performance of your Tennant Scrubber, consider the following: worn brush bristles (replace brushes); brush pressure set too light (increase brush pressure); main brushes not properly adjusted (adjust brushes); debris caught in main brush drive mechanism (remove debris); hopper is full (empty hopper); hopper lip skirts worn or damaged (replace lip skirts). If these steps don't resolve the issue, it may require calling a Tennant service representative.
Detailed physical and capacity specifications for the M30 model.
Physical and capacity specifications for the M20 model.
Provides guidance for troubleshooting electrical issues.
Locates various hydraulic components and systems on the machine.
Overview of maintenance procedures for M Series machines.
Information on electrical protection devices and their circuits.
Guide to accessing and navigating machine service modes.
Describes how to use the manual mode for testing components.
Utility for configuring optional equipment and output functions.
To Next Page
General
