Tennant M30 Service Manual (English)

Other manuals for Tennant M30

Service Information Manual170 pages

Operator's Manual120 pages

Instruction Bulletin12 pages

Questions and Answers:

A
Alexis LopezSep 6, 2025
How to troubleshoot a FaST System that does not operate on a Tennant M30?
- A
  Anthony HernandezSep 6, 2025
  If your Tennant Scrubber's FaST system isn't working, first make sure the FaST button is turned on. Check for clogs in the FaST?PAK supply hose and connector; if clogged, soak them in warm water and clean. Ensure the FaST?PAK carton isn't empty or disconnected, and replace or connect it as needed. Prime the system by operating it for a few minutes. Also, check for a clogged filter screen and clean it after draining the solution tank. If these steps don't resolve the issue, the fuse might be blown or the solution pump faulty, requiring a call to a Tennant service representative.
E
Eric BuchananSep 5, 2025
How to fix trailing water or poor water pickup on Tennant Scrubber?
- D
  donnarossSep 6, 2025
  If you notice trailing water or poor water pickup with your Tennant Scrubber, there are several potential causes. First, ensure the scrub vacuum fan is turned on. If it is, check the squeegee blades for wear and rotate or replace them if necessary. Also, verify the squeegee is properly adjusted. Other possible causes include a clogged vacuum hose or a dirty vacuum screen, which can be resolved by flushing the hose or cleaning the screen. Additionally, ensure there is detergent in the solution tank to prevent squeegee chatter. Check the recovery tank cover seals for wear and replace if needed. Remove any debris caught in the squeegee, and ensure the vacuum hose is properly connected and not damaged. Finally, confirm the recovery tank cover is completely closed and free of obstructions.
W
William WebsterSep 5, 2025
Why won't the scrub vacuum fan turn on in my Tennant Floor Machine?
- J
  James BeckSep 5, 2025
  If the scrub vacuum fan on your Tennant Floor Machine won't turn on, there are a few things to check: * Make sure the vacuum fan/squeegee button is turned on. * Drain the recovery tank if it is full. * Empty the recovery tank if it is filling with foam; use less detergent or a defoamer to prevent foaming. * Clean or replace the recovery tank sensor if it is dirty or stuck.
G
George VillegasSep 4, 2025
How to fix trailing water or poor water pickup with my Tennant Floor Machine?
- R
  rebeccamontgomerySep 4, 2025
  If the Tennant Floor Machine exhibits trailing water or poor water pickup, there are several potential causes and solutions: * Ensure the scrub vacuum fan is turned on. * Rotate or replace worn squeegee blades. * Adjust the squeegee if it is out of adjustment. * Add detergent to the solution tank to prevent squeegee chatter. * Flush any clogged vacuum hoses. * Clean the vacuum screen. * Replace worn recovery tank cover seals. * Remove any debris caught in the squeegee. * Reconnect or replace any disconnected or damaged vacuum hoses. * Ensure the recovery tank cover is completely closed and free of obstructions.
S
svaldezSep 3, 2025
What to do if sweeping or scrubbing functions don't turn on in Tennant Floor Machine?
- B
  Brian HuangSep 3, 2025
  If the sweeping or scrubbing functions on your Tennant Floor Machine aren't turning on, ensure the hopper is completely lowered. If there is a fire in the hopper, shut off the machine and extinguish the fire, call emergency personnel if necessary. If the recovery tank is full, press the Scrub vacuum fan/ squeegee button for one minute of extended water pickup and then empty the recovery tank. On ES models, activate the ES system to prevent this.
P
Patrick KleinAug 23, 2025
What to do if sweeping or scrubbing functions do not turn on in Tennant M30 Scrubber?
- P
  Peter WallAug 25, 2025
  If the sweeping or scrubbing functions on your Tennant Scrubber do not turn on, it might be due to the hopper being up. Completely lower the hopper. In some cases, the recovery tank may be full. Press the Scrub vacuum fan/squeegee button for one minute of extended water pickup and empty the recovery tank. For ES models, activate the ES system to prevent this. In the event of a fire in the hopper, shut off the machine, extinguish the fire, and if necessary, call emergency personnel.
J
jefferygeorgeSep 2, 2025
What to do if the vacuum fan won't turn on in Tennant Floor Machine?
- J
  Joel HodgeSep 2, 2025
  If the scrub vacuum fan on your Tennant Floor Machine isn't turning on, first check if the vacuum fan/squeegee button is activated. If the recovery tank is full, drain it. Foam in the recovery tank can also cause this issue, so empty the tank. You may need to use less detergent or a defoamer. Lastly, the recovery tank sensor might be dirty or stuck; try cleaning or replacing it.
A
Andrew KiddSep 1, 2025
Why is my Tennant Floor Machine leaving water?
- T
  Todd SparksSep 1, 2025
  If the Tennant Floor Machine leaves water behind, several factors could be at play. First, ensure the vacuum fan is turned on. Check the squeegee blades for wear and rotate or replace them if needed. Adjust the squeegee if it's out of alignment. Adding detergent to the solution tank can also help. Other potential issues include a clogged vacuum hose (flush it), a dirty vacuum screen (clean it), worn recovery tank cover seals (replace them), debris caught in the squeegee (remove it), a disconnected or damaged vacuum hose (reconnect or replace it), or a recovery tank cover that isn't completely closed (check for obstructions and ensure it's properly closed).
O
olozanoAug 31, 2025
Why is my Tennant M30 Scrubber not scrubbing well?
- M
  Ms. Susan Bauer DDSSep 1, 2025
  If your Tennant Scrubber isn't scrubbing well, the issue might be due to improper detergent or brushes. Another reason could be that the solution tank is empty, so you should fill it. Also, check for any debris caught on the main brushes and remove it.
R
Randy GonzalezAug 31, 2025
What to do if there is little or no solution flow in Tennant Scrubber?
- E
  Eric HernandezAug 31, 2025
  If you're experiencing little or no solution flow to the floor in your Tennant Scrubber, first check if the solution tank is empty and fill it if necessary. If the tank isn't empty, ensure that the solution flow is turned on. If the problem persists, the solution supply lines may be plugged, requiring you to flush them.