Tennant T15 User Manual (English)

Other manuals for Tennant T15

Questions and Answers:

N
Nancy KingAug 17, 2025
Why is my Tennant T15 Scrubber not picking up water?
- J
  Jennifer LeeAug 17, 2025
  If your Tennant Scrubber isn't picking up water, it could be due to several reasons: * Squeegee blades may be worn, requiring rotation or replacement. * The squeegee might need adjustment. * The vacuum hose could be clogged and needs flushing. * A dirty vacuum fan inlet filter can restrict airflow, so clean it. * Debris caught on the squeegee can impede water pickup; remove it. * A disconnected or damaged vacuum hose to the squeegee or recovery tank should be reconnected or replaced. * Ensure the tank cover is completely closed, checking for any obstructions. * Torn seals on the recovery tank should be replaced.
L
Luke SmithAug 20, 2025
What to do if Tennant T15 has trailing water?
- M
  michelle77Aug 20, 2025
  If your Tennant Scrubber is leaving water behind, here's what you can do: * Check for worn squeegee blades and rotate or replace them. * Adjust the squeegee if it's out of alignment. * Flush any clogs from the vacuum hoses. * Clean the vacuum fan inlet filter if it's dirty. * Remove any debris caught on the squeegee. * Reconnect or replace the vacuum hose if it's disconnected or damaged. * Ensure the tank cover is completely closed, checking for obstructions. * Replace any torn seals on the recovery tank.
K
Katie AlvarezAug 25, 2025
How to improve scrubbing performance of Tennant T15 Scrubber?
- L
  Lisa SullivanAug 25, 2025
  To enhance the scrubbing performance of your Tennant Scrubber, consider the following: * Remove any debris caught on the scrub brushes. * Replace worn scrub brushes. * Reset the scrub brush motor circuit breaker(s) if tripped. * Reduce scrub brush down pressure. * Level the scrub head to ensure even brush pressure. * If using a cylindrical scrub head, replace any broken brush drive belts. * Charge batteries until the charger automatically turns off if there is a low battery charge.
I
Isabella SmithAug 28, 2025
What to do if Tennant T15 Scrubber has little or no solution flow?
- C
  Courtney JohnstonAug 28, 2025
  If your Tennant Scrubber isn't dispensing enough solution, try these steps: * Fill the solution tank if it's empty. * Replace and/or adjust the solution control rod if it's broken or misaligned. * Ensure the solution flow is turned on. * Flush the solution supply lines to clear any blockages. * Clean or replace the solution solenoid if it's clogged or stuck. * If equipped with ES mode, ensure the ES switch is turned on.
R
russelldiazAug 31, 2025
What to do if Tennant T15 has poor sweeping performance?
- J
  johnbrownSep 1, 2025
  If your Tennant Scrubber's sweeping isn't up to par, here's what you can check: * Replace worn brush bristles. * Adjust the sweeping brushes. * Empty the hopper if it's full. * Replace hopper skirts if they are worn or damaged.
T
Todd WilliamsSep 4, 2025
How to fix Tennant T15 Scrubber when vacuum fan will not turn on?
- B
  Brian BrownSep 4, 2025
  If the vacuum fan on your Tennant Scrubber won't turn on, check these: * Drain the recovery tank if it's full. * Empty the recovery tank if it's filling with foam, and consider using less detergent or switching to a different one, or use a defoamer. * Reset the vacuum fan circuit breaker if it has tripped.
D
Deborah DunnSep 8, 2025
How to fix FaST system on Tennant T15 Scrubber?
- J
  Julia EdwardsSep 8, 2025
  If the FaST system on your Tennant Scrubber isn't working, consider the following: * Ensure the FaST switch is turned on. * Reset the 15A circuit breaker button after determining the cause of the trip. * Soak the FaST PAK supply hose and connector in warm water to clean any clogs. * Replace the FaST PAK carton if it's empty or not connected, and ensure the supply hose is connected. * Prime the system by operating the FaST solution system for 5 to 10 minutes. * Remove and clean the flow control orifice/screen if clogged. * Drain solution tank, remove and clean filter screen.