To Next PageTo Next Page
Need help?Do you have a question about the TestPad BTS-2002H and is the answer not in the manual?
Describes static test parameters like voltage, impedance, charge/discharge, and resistance tests.
Details testing battery capacity through charge and discharge cycles.
Explains using the tester as a smart recharger for various battery types.
Describes the function to discharge batteries and control the cut-off voltage.
Details using the tester as a digitally-controlled DC power supply.
Explains the tester's function as a digitally-controlled electronic loading unit.
Describes using the tester as a voltmeter and milliohm meter.
Explains how to calibrate the tester for accurate measurements.
Details reading data from DS2502-compatible IDs.
Describes the tester's LCD display capabilities and layout.
Details the six light touching buttons for operating the tester.
Explains the seven connection terminals on the tester and their functions.
Illustrates the connection for testing a Li-ion battery with identification resistors.
Illustrates the multi-level menu structure of the tester.
Provides descriptions for the main menu options available on the tester.
Details setting parameters for battery type, voltage, capacity, charge, and discharge tests.
Defines thresholds for voltage, impedance, over-current, and identification resistors.
Configures settings for ID testing and short-circuit protection tests.
Sets maximum voltage drop and the exit mode for saving settings.
Details configuration options for battery pack type and voltage.
Explains settings for battery capacity, charge, discharge, and over-current tests.
Configuration for identification resistors R1 and R2 minimum and maximum values.
Settings for ID type, short-circuit test enabling, duration, and restoration.
Defines maximum voltage drop and exit mode for saving/resetting configurations.
Outlines the step-by-step process the tester follows during a static test.
Explains the display of voltage, impedance, and identification resistor results.
Explains common test messages and failure codes for static tests.
Maps common IDs to specific mobile phone models for identification.
Sets parameters for Li-ion battery capacity testing, including OC/OD.
Sets parameters for NiCd battery capacity testing, including pre-discharge.
Outlines the sequence of charge, discharge, and protection tests for capacity measurement.
Details how charged and discharged capacity are accumulated and displayed.
Explains various indicators and abbreviations used during capacity testing.
Interprets test status indicators, accumulated duration, voltage, current, and capacity.
Explains how the tester handles faults and displays error causes.
Illustrates the interface for the DC power supply mode, showing settings and output.
Explains how to start, stop, adjust, and exit the DC power supply mode.
Illustrates the interface for the electronic load mode, showing mode, settings, and output.
Describes the four supported electronic load modes: constant current, voltage, resistance, power.
Details cut-off voltage function and output status indicators.
Explains how to switch modes, adjust values, enable/disable, and exit the electronic load mode.
Lists the parameters displayed in VOL and IMP mode: voltage, impedance, and resistors.
Explains special indications for reverse connection and out-of-range measurements.
Explains that measurement accuracy can be calibrated for voltage, impedance, currents, etc.
Requires a password for accessing the calibration function to prevent unauthorized access.
Describes connecting the ID terminal and cathode to read DS2502 data.
Explains the interpretation of DS2502 ROM code, serial number, and CRC data.
Details viewing data by address and verifying data integrity using CRC.
Indicates potential errors like abnormal chip or poor contact during data reading.
Specifies the operating temperature, altitude, and relative humidity requirements.
Details the measurement ranges and minimum resolutions for various parameters.
Provides the testing speed for static and capacity tests.
Specifies the measurement accuracy for voltage, current, impedance, and capacity.
Details the maximum voltage, current, and power for the DC E-load function.
Provides specifications for power supply, consumption, weight, and dimensions.
Warns about proper calibration by technicians and its necessity for accurate measurements.
Lists the parameters of the tester that can be calibrated for accuracy.
Details the necessary components and materials for performing tester calibration.
Provides detailed steps for calibrating voltage and charge current using external sources.
Provides detailed steps for calibrating discharge current and over-current protection.
Details calibration steps for impedance and correcting connection line resistance.
Explains how to save calibration settings and restore default calibration settings.
General| Brand | TestPad |
|---|---|
| Model | BTS-2002H |
| Category | Test Equipment |
| Language | English |
