Texas Instruments PCM186xEVM - Page 18

Schematics, Bill of Materials and Layouts www.ti.com
Table 4. Bill of Materials for PCM186xEVM (continued)
Item MANU PART NUM MANU Qty REF DES Description
31 CRCW040210K0FKED VISHAY 4 R30, R31, R32, R33 RESISTOR SMD0402 10.0K OHMS 1% 1/16W ROHS
32 ERJ-3EKF1002V PANASONIC 1 R37 RESISTOR SMD0603 10.0K 1% THICK FILM 1/10W ROHS
33 CRCW0402360RFKED VISHAY 1 R38 RESISTOR SMD0402 360 1/16W 1% ROHS
34 ERJ-3EKF3570V PANASONIC 1 R34 RESISTOR SMD0603 357 OHM 1% THICK FILM 1/10W ROHS
35 ERJ-2RKF1003X PANASONIC 8 R40, R41, R42, R43, R44, R45, RESISTOR SMD0402 THICK FILM 100K OHMS 1/16W 1% ROHS
R46, R47
36 ERJ-3GEY0R00V PANASONIC 8 MD0(Byp), MD1/AD(Byp), RESISTOR SMD0603 0.0 OHM 5% THICK FILM 1/10W ROHS
MD3/MC/SCL(Byp),
MD4/MISO/GPIO(Byp),
INT/GPIO3/INTC(Byp),
DOUT2/MD2/MOSI/SDA(Byp),
MD5/GPIO1/INTA/DMIN(Byp),
MD6/GPIO2/INTB/DMCLK(Byp)
37 PPPC082LJBN-RC SULLINS 1 J1 HEADER THRU FEMALE-RA 2X8 100LS 120 TAIL GOLD ROHS
38 PBC02SAAN SULLINS 0 J2, J3, J4, J5 HEADER THRU MALE 2 PIN 100LS 120 TAIL GOLD ROHS
39 PBC02SAAN SULLINS 6 J6, J8, J9, J10, J11, VOUT HEADER THRU MALE 2 PIN 100LS 120 TAIL GOLD ROHS
40 PBC08DAAN SULLINS 1 J7 HEADER THRU MALE 2X8 100LS 120 TAIL GOLD ROHS
41 CTP-019-8 CONNECT TECH PRODUCTS 4 VIN1, VIN2, VIN3, VIN4 JACK DUAL RCA RA-PCB METAL SHELL ROHS
42 4015-0-67-80-30-27-10-0 MILL-MAX 2 XI, XO PIN SOCKET .015-.025in 70x55x1.0in GOLD ROHS
Y0 IS INSERTED INTO XI AND XO PIN SOCKETS
43 ECS-245.7-20-4X ECS 1 Y0 CRYSTAL HC-49USX 24.576MHz SERIES 30ppm 20pfd FUND ROHS
44 5003 KEYSTONE ELECTRONICS 16 1L, 1R, 2L, 2R, 3L, 3R, 4L, 4R, PC TESTPOINT ORANGE ROHS
BCK, DIN, SCL, SDA, DOUT,
LRCK, SCKI, MICBIAS
45 TL1015AF160QG E-SWITCH 1 RESET SWITCH, MOM, 160G SMT 4X3MM ROHS
46 95947A121 MCMASTER-CARR 4 STANDOFFS STANDOFF M3x12mm 4.5mm DIA HEX ALUM F-F ROHS
47 92148A150 MCMASTER-CARR 4 STANDOFF WASHERS WASHER SPLIT-LOCK M3 6.2mm OD 0.7mm THICK STAINLESS STEEL ROHS
48 92000A118 MCMASTER-CARR 4 STANDOFF SCREWS SCREW M3x8 PHILIPS PANHEAD STAINLESS STEEL ROHS
TOTAL 138
Special notes to this bill of materials
SN1 These assemblies are ESD sensitive, observe ESD precautions.
SN2 These assemblies must be clean and free from flux and all contaminants. Use of no clean flux is not acceptable.
SN3 These assemblies must comply with workmanship standards IPC-A-610 Class 2.
18
PCM186xEVM SLAU615–December 2014
Submit Documentation Feedback
Copyright © 2014, Texas Instruments Incorporated