TEXIO PSF-1200L

To Next Page

To Previous Page

Main Page

Table of Contents2
Using the Product Safely6
General10
Applicable Products10
Features12
Accessories13
Specifications14
3．Preliminary Instructions22
Devices on Panels24
Front Panel24
Rear Panel28
Operation Procedures32
Connecting AC Power Cable32
Connecting Load with Output Terminals32
Connection with the Rear Output Terminals32
Connection with the Front Output Terminals35
Operation Ranges36
Various Setting36
How to Set Voltage37
How to Set Current37
How to Set Power37
How to Change into Power Display38
How to Output38
How to Display the Set Value in Outputting Condition39
How to Rotate Display Panel by 90 Degrees (for Vertical Installation)40
How to Invalidate On-Panel Operations (Key Lock Function)40
Various Functions Available on Menus41
Preset Function (01)42
OVP/OCP Function (02)43
Hi-Ωfunction (03)44
OFF Timer Function (04)45
Sequence Function (05)47
External Control (External Voltage, External Resistance) (06)50
External Control (On/Off) (07)52
Delay Function (08)53
Tracking Function (09)55
Master-Slave Function (10)56
Output Voltage Remote Sensing58
External Control Functions59
To Assemble the Connector XG5M-2635-N59
Output Voltage Monitor and Output Current Monitor60
Constant-Voltage (CV) Control with External Voltage or Resistance61
Constant-Current (CC) Control with External Voltage or Resistance62
Output ON/OFF with External Contacts63
Alarm Function Using External Contacts64
Various Status Signals (CV, CC & ALARM)65
Activating Output When Turning on Power66
Usage of Sequence Function66
Other Functions68
Display in Alarm Status68
One-Control Parallel Operation (Excluding PSF-400L2)69
One-Control Series Operation (Excluding PSF-400L2)71
Power Extension Using PSF-800LS (Parallel Connection Only)72
How to Use the PSF-800LS73
Master-Slave Connection Using Optional Kits74
Accessories77
Interface Boards77
Option77
External Control through Interface Board78
Remote Control78
Interface Connectors78
Specifications79
Specifications of IF-60RU79
Specifications of IF-60GP80
Connection Methods81
Connection Cables82
Address Setting82
Using Interface Boards84
Using the GP-IB Interface84
Using the USB Interface85
Using the RS-232C Interface85
Using the Local Bus86
Communication Commands86
Command List87
Output Voltage Setting (：VOLT)88
OVP Setting (：VOLT：PROT)88
Output Current Setting (：CURR)89
OCP Setting (：CURR：PROT)90
Output Power Setting (：POW)91
Output On/Off (：Outp)92
Hi-ΩON/OFF (：CONF：HIZ)92
Hi-Ωtime Setting (：CONF：HIZ：HOLD)93
Display Switching (：CONF：DISP)93
Tracking ON/OFF (：CONF：TRAC)94
External Control Setting (：EXT：MOD)94
External Output Voltage Control ON/OFF (：EXT：VOLT)95
External Output Current Control ON/OFF (：EXT：CURR)95
Output Switching (：EXT：OUTP)96
Off Timer ON/OFF (：TIMER：MOD)96
Off Timer Value Setting (：TIMER：SET)97
Delay Function ON/OFF (：DELAY：MOD)97
Delay Rise Time Setting (：DELAY：RISE)98
Delay Fall Time Setting (：DELAY：FALL)98
Monitor Inquiry (：MEAS?)98
Preset Calling (：PRES：CALL)99
Preset Saving (：PRES：SAVE)99
Sequence Mode Setting (：SEQ：MOD)100
Sequence Jump Setting (：SEQ：STEP)100
Sequence Start Step Setting (：SEQ：START)100
Sequencer End Step Setting (：SEQ：END)101
Sequence Repetition Frequency Setting (：SEQ：CYCL)101
Sequence Data Transfer (：SEQ：DOWNLOAD)101
Model Inquiry (＊IDN?)102
Event Register Inquiry (＊ESR?)102
Event Enable Register Setting (＊ESE)102
Status Byte Inquiry (＊STB?)102
SRQ Enable Register Setting (＊SRE)102
Buffer Clear (＊CLS)102
Communication Reset (＊RST)103
Command Completion (＊OPC)103
Wait for Completion (＊WAI)103
Local Address Setting (：ADDR)104
Remote/Local Setting (：REMOTE)104
Registers105
Status Register (STB、SRE)106
Event Register (ESR、ESE)107
Function of the Status Byte108
Reading Data from the Status Byte and Clearing the Status Byte109
Clear and Reset Statuses110
Remote/Local Function111
Responses to Multi-Line Message Commands112
Troubleshooting113
Maintenance114
Outside Dimensions116
Specification of PSF-1200L/1600L118

Related product manuals

TEXIO PSF-1200L - Page 5

Table of Contents

Related product manuals