13
Chapter title
EN
13
General operation
Switching the TV set on and off
• To switch the TV set on:
- press the
button on the side of the TV set, the or
OK on the remote control to switch the television on at the
last channel or AV programme you were watching,
- press the
TV or PR+/PR- buttons to switch the television
on at the last channel you were watching,
- press any numeric button to switch the television on at the
corresponding channel,
- press the AV button to switch the television on at the last AV
programme you were watching.
• To put the TV set into standby mode, press the button
on the side of the TV set or the
button on the remote
control. The TV set remains powered up, but with low energy
consumption.
• To switch off the TV set, unplug the mains socket from the
mains outlet.
Accessing channels
• Using the numeric buttons:
w for channels 1 to 9, press the corresponding numeric button;
w for channels 10 to 99,
- press the tens digit for a few seconds to display it on
the screen, then press the units digit. For instance, for
programme 24, press and hold
2 to display 2-, then press
4; or
- press the
0/-- button to display “--”, then enter the two
digits.
• Using the PR+/PR- buttons: scroll through the channels. AV
programmes are not included in the cycle unless you use the
buttons on the side of the TV set.
• Using the list of programmes: refer to page 14.
To access the channel or AV programme previously being watched,
press the
CANCEL button.
Accessing your favourite channels
(analogue reception only)
You can defi ne the channels you watch most often as your favourite
channels. This will allow you to create your own list of channels
which you can access more quickly using the
PR+/PR- buttons on
the remote control.
1. Follow the procedure described in point 5 on page 11 for
defi ning a channel as your favourite channel.
2. Press the PRESETS button on the remote control.
3. Select the PR+/PR- keys option. Use the buttons to
select
Favourites.
When you change channels using the
PR+/PR- buttons on the
remote control only your favourite channels will be available.
To cancel this option, select All channels under the PR+/PR-
keys option.
Note: The PRÅÇ buttons on the TV set allow you to access all the
channels set up, even if the
Favourites option is selected.
Accessing AV programmes
Press the AV button to display the last selected audio-visual
programme and scan through the other audio-visual programmes.
AV selection loop: AV1, AV2, AV3, CMP (= component, YPrPb or
YCrCb), VGA, HDMI.
Volume
• Volume control: use the É VOL Ñ buttons on the side of the
TV set or press the
+/- buttons on the remote control to
increase or decrease the volume.
• Sound mute: press the button to temporarily mute the
sound. Press this button again or the
+ button to restore it.
• Headphone volume control: press the +/- buttons on the
remote control to display the volume control bar. Then use the
buttons to switch to the headphone volume control bar.
Use the
+/- buttons to adjust the volume.
Displaying status information
Analogue reception
• In TV mode you can press the INFO button on the remote
control to display the number and name of the relevant channel,
the time and date, the type of sound and format or zoom. If the
turn-off timer is set the relevant symbol is displayed, along with
the time remaining until the TV set is switched off.
Press the
GUIDE button on the remote control to display the
name and the start time for the current programme and the
following programme. If this information is not available you will
receive a message to this effect.
• In PC mode you can press the INFO button on the remote
control to display the time and date, the type of sound and
format, as well as the source of the signal being received and
the resolution. If the sleep or turn-off timer is set the time
remaining until the TV set is switched into stand by is displayed.
When you switch the TV set on, change channels or exit Teletext,
the channel’s number and name are displayed.
Note: If you activate the Channel number function in the
Preferences menu, the channel number will be displayed
permanently (see page 21).
Digital reception
• In TV mode, press the INFO button on the remote control to
display the date and time, the name, start time and duration
of the current programme, the name and start time of the
following programme.
Press the
GUIDE button on the remote control to display the
name and the start time for the current programme and the
following programme. If this information is not available you will
receive a message to this effect.
• A menu also appears allowing you to select the language for the
subtitles, the language for the audio and sound type.
The
channels option can be used to fi nd current and future
programmes showing on the other channels. Use the
buttons to display the information and press
OK to display the
channel you want.
130-EN-DVBT.indd 13130-EN-DVBT.indd 13 26/01/06 14:19:1026/01/06 14:19:10
To Next Page
Loading...
