Why cooling fan always rotates at fast speed on my Toro Lawn Mower?
If the cooling fan on your Toro Lawn Mower always rotates at a fast speed, inspect the proportional relief valve (PRV) for faults and replace it as necessary.
Why is the hydraulic system on my Toro 30446 operating hot?
If the hydraulic system in your Toro Lawn Mower is operating hot, there could be several reasons. First, increase the engine RPM. Ensure the brakes are not applied or sticking; release or fix them if they are. Refill the hydraulic reservoir if the oil level is low. If the hydraulic oil is contaminated or incorrect, replace it with the correct type. Other potential causes include an open or damaged piston pump bypass valve (repair or replace it), a cooling system not operating properly (fix or replace components), low charge pressure (check and adjust), incorrect traction circuit pressure (check and adjust), or damaged pumps or motors (repair or replace them).
Why is hydraulic oil in reservoir foaming in my Toro 30446 Lawn Mower?
If the hydraulic oil in the reservoir of your Toro Lawn Mower is foaming, it could be due to a low oil level in the hydraulic reservoir; if that's the case, refill it. It may also be caused by using the wrong type of oil in the hydraulic system, so replace it with the correct hydraulic oil. Another possible cause is air leaking into a pump suction line, so seal any air leaks in the pump suction line.
What to do if my Toro 30446 Lawn Mower has lost traction power or won't operate?
If your Toro Lawn Mower is losing traction power or won't operate in either direction, start by refilling the hydraulic reservoir oil if the level is low. Other possible causes include an open or damaged piston pump bypass valve (repair or replace it), low charge pressure (check and adjust), low traction circuit pressure (check and adjust), or damaged front wheel motor couplers (repair or replace them).
Why cooling fan does not rotate on my Toro 30446?
If the cooling fan does not rotate on your Toro Lawn Mower, inspect the fan motor for wear or damage and replace it as necessary. Check the gear pump section for the engine cooling fan circuit for wear.
What to do if my Toro Lawn Mower has lost traction power?
If your Toro Lawn Mower loses traction power or doesn't operate in either direction, ensure the hydraulic reservoir is filled to the correct level. Inspect the piston pump bypass valve for proper operation. Check and correct the charge and traction circuit pressure. Also, inspect the front wheel motor couplers and replace them if they are damaged.
What to do if hydraulic oil in Toro 30446 Lawn Mower reservoir foams?
If the hydraulic oil in the reservoir is foaming, it could be due to a few reasons. First, check the hydraulic reservoir oil level and refill if it's low. Ensure that you are using the correct hydraulic oil for the system. Another possible cause is air leaking into the suction line, so repair any air leaks you find there.
Why is the steering in my Toro 30446 Lawn Mower inoperative or sluggish?
If the steering on your Toro Lawn Mower feels inoperative or sluggish, start by inspecting steering components such as tie rods and steering cylinder ends for wear or binding. Free up any binding in the steering cylinder. Ensure the hydraulic reservoir has enough oil. Check the steering relief valve for proper function and inspect the steering cylinder for internal leaks. Also, check the steering control valve and gear pump section for any signs of wear or damage.
Why no cutting decks will operate on my Toro 30446 Lawn Mower?
If all the cutting decks on your Toro Lawn Mower won't operate, the gear pump or its coupler may be damaged; repair or replace the damaged gear pump or coupler.
Why all cutting decks operate slowly on my Toro Lawn Mower?
If the cutting decks on your Toro Lawn Mower are operating slowly, increase the engine RPM if it's low. Damaged deck motor or gear pump sections could also be the cause, so repair or replace them.
General| Cutting Width | 22 in |
|---|---|
| Drive Type | Self-Propelled |
| Deck Material | Steel |
| Weight | 80 lbs |
| Power Source | Gasoline |
| Cutting Height | 1.25 - 3.75 in |
| Starting System | Recoil |
| Mulching Capability | Yes |
| Bagging Capability | Yes |
| Side Discharge Capability | Yes |
| Engine | Briggs & Stratton® |
| Wheel Size | 11 inches (rear) |
To Next Page
