Toro 30446 - User Manual

Other manuals for Toro 30446

Questions and Answers

K
kdiazAug 30, 2025
What to do if my Toro 30446 travels too far before stopping?
- C
  Cheryl MaciasAug 30, 2025
  If your Toro Lawn Mower travels too far before stopping when you release the traction pedal, the traction linkage may be out of adjustment; adjust it. Also, check and adjust the charge pressure, as low pressure can cause this issue. Another potential cause is plugged or damaged piston (traction) pump servo control valve orifices, which should be cleared or replaced. Finally, if the traction pedal does not return to neutral, repair or adjust it.
A
Antonio MendezAug 29, 2025
Why is the traction pedal sluggish on my Toro Lawn Mower?
- A
  Adrian ZhangAug 29, 2025
  If the traction pedal on your Toro Lawn Mower feels sluggish, it could be due to a stuck or binding traction control linkage; free or repair it. Low charge pressure could also be the cause, so check and adjust it. Additionally, the piston (traction) pump servo control valve orifices might be plugged or damaged, requiring clearing or replacement. Leaking or damaged seals on the 4WD manifold PD1 and PD2 pilot directional valves could also be the cause; repair or replace them.
D
Daniel OrtizAug 28, 2025
Why my Toro 30446 operates in one direction only?
- A
  Anthony WeaverAug 28, 2025
  If your Toro Lawn Mower only operates in one direction, the issue might be a faulty traction control linkage; in that case, repair or replace it. Alternatively, the traction relief valve could be defective, requiring replacement.
P
Paul JonesAug 27, 2025
Why cutting decks will not raise on my Toro 30446 Lawn Mower?
- J
  Jessica MorganAug 27, 2025
  If the cutting decks on your Toro Lawn Mower won't raise, first, increase the engine RPM if it's too low. If the hydraulic oil level in the reservoir is low, refill it. Check for binding lift arm pivots and free or repair them if necessary. Other potential issues include a stuck relief valve in the lift/lower control valve (repair or replace), a damaged or sticking pilot valve in the lift/lower control valve (repair or replace), damaged lift cylinder(s) (repair or replace), or an inefficient gear pump section for the lift/lower control valve (repair or replace).
S
Shawn ScottAug 27, 2025
What to do if my Toro 30446 Lawn Mower has lost traction power or won't operate?
- J
  James LopezAug 27, 2025
  If your Toro Lawn Mower is losing traction power or won't operate in either direction, start by refilling the hydraulic reservoir oil if the level is low. Other possible causes include an open or damaged piston pump bypass valve (repair or replace it), low charge pressure (check and adjust), low traction circuit pressure (check and adjust), or damaged front wheel motor couplers (repair or replace them).
I
ijohnsonAug 25, 2025
Why is hydraulic oil in reservoir foaming in my Toro 30446 Lawn Mower?
- B
  Bobby GomezAug 26, 2025
  If the hydraulic oil in the reservoir of your Toro Lawn Mower is foaming, it could be due to a low oil level in the hydraulic reservoir; if that's the case, refill it. It may also be caused by using the wrong type of oil in the hydraulic system, so replace it with the correct hydraulic oil. Another possible cause is air leaking into a pump suction line, so seal any air leaks in the pump suction line.
J
Joshua MooreAug 25, 2025
Why is the hydraulic system on my Toro 30446 operating hot?
- T
  Tiffany BennettAug 25, 2025
  If the hydraulic system in your Toro Lawn Mower is operating hot, there could be several reasons. First, increase the engine RPM. Ensure the brakes are not applied or sticking; release or fix them if they are. Refill the hydraulic reservoir if the oil level is low. If the hydraulic oil is contaminated or incorrect, replace it with the correct type. Other potential causes include an open or damaged piston pump bypass valve (repair or replace it), a cooling system not operating properly (fix or replace components), low charge pressure (check and adjust), incorrect traction circuit pressure (check and adjust), or damaged pumps or motors (repair or replace them).

Toro 30446 Specifications

General

Cutting Width	22 in
Drive Type	Self-Propelled
Deck Material	Steel
Weight	80 lbs
Power Source	Gasoline
Cutting Height	1.25 - 3.75 in
Starting System	Recoil
Mulching Capability	Yes
Bagging Capability	Yes
Side Discharge Capability	Yes
Engine	Briggs & Stratton®
Wheel Size	11 inches (rear)