Toro Groundsmaster 4100-D 30411 - Pushing or Towing the Machine

•Raiseeitherwingcuttingunittothetransport
position.Thecuttingunitshouldturnoff.Ifthe
cuttingunitdoesnotstop,thereisamalfunctionin
theinterlocksystemthatshouldbecorrectedbefore
resumingoperation.
•Ifthecuttingunitisloweredagainthemotorshould
re-start.Ifthecuttingunitdoesnotre-start,thereis
amalfunctionintheinterlocksystemthatshouldbe
correctedbeforeresumingoperation.
•Raisethecentercuttingunittothetransport
position.Allthecuttingunitsshouldstoprunning
andnotre-engagewhenloweredtotheground.If
thecuttingunitdoesnotstopwhenitisraisedorif
itre-startswhenitislowered,thereisamalfunction
intheinterlocksystemthatshouldbecorrected
beforeresumingoperation.
•Withthecuttingunitsengaged,switchthespeed
rangefromlowtohigh.Thecuttingunitsshould
stop.Ifthecuttingunitsdonotstop,thereisa
malfunctionintheinterlocksystemthatshouldbe
correctedbeforeresumingoperation.
•Iftheoperatorrisesfromtheseatwiththecutting
unitsengagedand/orthetractionpedaloutof
neutral,thecuttingunitsmuststopinapproximately
onesecondandenginemustshutdownin
approximatelytwoseconds.Ifthecuttingunitsdo
notstopandtheenginedoesnotshutdown,thereis
amalfunctionintheinterlocksystemthatshouldbe
correctedbeforeresumingoperation.
PushingorTowingthe
Machine
Inanemergency,themachinecanbemovedforwardby
actuatingthebypassvalveinthevariabledisplacement
hydraulicpumpandpushingortowingthemachine.
Donotpushortowthemachineformorethan1/4
mile(0.4km).
Important:Donotpushortowthemachine
fasterthan2-3MPH(3-4.8km/h)becauseinternal
transmissiondamagemayoccur.Thebypassvalve
mustbeopenwheneverthemachineispushedor
towed.
1.Raisetheseatandremovethebatterycover.The
bypassvalveislocatedinfrontofthebattery
(Figure28).
2.Rotatethevalve90degrees(1/4turn)ineither
directiontoopenandallowoiltobypassinternally.
Becauseuidisbypassed,themachinecanbeslowly
movedwithoutdamagingthetransmission.
Note:Resistancewillbefeltonthevalvewhenitis
movedtotheopenposition.
3.Rotatethevalve90degrees(1/4turn)backto
closethebypassvalvebeforestartingtheengine.
However,donotexceed5to8ft-lb(7to11N⋅m)
torquetoclosethevalve.
Figure28
1.Bypassvalveaccesshole
Important:Ifthemachinemusttobe
pushedortowedinreverse,thecheckvalve
inthefour-wheeldrivemanifoldmustalsobe
bypassed.Tobypassthecheckvalve,connect
ahoseassembly(HosePartNo.95-8843,
CouplerFittingNo.95-0985[Qty.2],and
HydraulicFittingNo.340-77[Qty.2])tothe
reversetractionpressuretestport(Figure29)
andthereversefour-wheeldrivepressureport
(Figure30).
Figure29
1.Reversetractionpressuretestport
30