*
1 Only a part of indoor unit types is installed with the discharge air temperature sensor. This temperature is not displayed for other types.
*2 When the units are connected to a group, data of the header indoor unit only can be displayed.
*3 The first digit of an CODE No. indicates the outdoor unit number.
*4 The upper digit of an CODE No. -4 indicates the outdoor unit number.
1 , 5 ... U1 outdoor unit (Header unit)
2 , 6 ... U2 outdoor unit (Follower unit 1)
*
5 Only the CODE No. 9* of U1 outdoor unit (Header unit) is displayed.
tamrof yalpsiDeman ataD.oN EDOC Unit Remote controller display example
Indoor unit data *
2
00
Room temperature (Use to control)
×1 °C
[0080]= 80 °F
01 Room temperature (Remote controller) ×1 °C
°F
1×
Indoor suction air temperature (TA)
20
°F
1×)JCT( erutarepmet lioc roodnI30
°F
1×)2CT( erutarepmet lioc roodnI40
°F
1×)1CT( erutarepmet lioc roodnI50
06
Indoor discharge air temperature (TF) *
1
×1 °F
[0150]= 1500pls
slp01/1×gninepo VMP roodnI80
System data
stinu 84=]8400[tinu1×stinu roodni detcennoc fo .oNA0
0B Total horsepower of connected indoor units ×10
ton [0215]=21.5 ton
[0003]=3 units
tinu1×stinu roodtuo detcennoc fo .oNC0
[0120]=12 tonton
01×stinu roodtuo fo rewopesroh latoTD0
F9
Suction temperature of air to air heat
exchanger (TSA)
*1
×1
FA
Outside air temperature (TOA)
*1
×1
U1 U2 U3
10 20 30
psi
11 21 31
psi
12 22 32
13 23 33
15 25 35
16 26 36
19 29 39
1A 2A 3A
1B 2B 3B
1D 2D 3D
U1 U2 U3
50 60 70 pls
51 61 71 pls
52 62 72 pls
53
63 73 A
54
64 74 A
56 66 76 rps
57 67 77 rps
59 69 79 mode
5A 6A 7A
5B 6B 7B
5D 6D 7D
5E 6E 7E
5F 6F 7F
Unit
Outdoor unit
individual data 3
*5
90 Heating/cooling recovery controlled
0: Normal
1: Recovery controlled
[0010]=Heating recovery controlled
[0001]=Cooling recovery controlled
91 Pressure release
0: Normal
1: Release controlled
[0010]=Pressure release controlled
92
CODE No. Data name Display format Remote controller display example
Discharge temperature release [0001]=Discharge temperature release controlled
93
Follower unit release
(U2 outdoor units)
[0100]=U2 outdoor unit release controlled
Compressor IPDU 2 heat sink temperature ×1
Outdoor fan IPDU 1 heat sink temperature ×1
Outdoor fan IPDU 2 heat sink temperature ×1
Outdoor unit horsepower ×1
[0080] = 8 ton
[0135] = 13.5A
1 fan model : Compressor 2 and Outdoor fan 1 current (I2)
2 fan model : Compressor 2 and Outdoor fan 2 current (I2)
×10
Compressor 1 revolutions ×10
[0642] = 64.2rps
Compressor 2 revolutions ×10
Outdoor unit individual data 2
*4
PMV1 opening ×1
[0500] = 500plsPMV3 opening ×1
PMV4 opening ×1
1 fan model : Compressor 1 curent (I1)
2 fan model : Compressor 1 and Outdoor fan 1 current (I1)
×10
Outdoor fan mode ×1 [0058] = 58 mode
Compressor IPDU 1 heat sink temperature ×1
[0024] = 24 °F
CODE No.
Data name Display format Unit Remote controller display example
Temperature at liquid side (TL1) ×1
Outdoor unit individual
data 1
*3
High-pressure sensor detention pressure (PD) ×100
[4350] = 435 psi
Low-pressure sensor detention pressure (PS)
×100
Compressor 1 discharge temperature (TD1) ×1
Outside ambient temperature (TO)
×1
Suction temperature (TS1)
×1
Suction temperature (TS2)
×1
[0080] = 80 °F
Compressor 2 discharge temperature (TD2) ×1
Outdoor coil temperature (TE1) ×1
Outdoor coil temperature (TE2) ×1
CODE No.
Data name Display format Unit Remote controller display example
− 132 −
F3
Filter sign time
×1 h [2500]= 2500h
[0027]= 27°C
°F
°F
[0080]= 80 °F
°F
°F
°F
°F
°F
°F
°F
°F
°F
°F
°F
°F
ton
To Next Page
Loading...
