Toshiba Q9+ - Page 3

306 pages

To Next Page

To Next Page

To Previous Page

To Previous Page

Loading...

Document Number: 68249-003

April, 2020

Q9 Plus ASD

Installation & Operation Manual

®

Table of Contents

Electrical Hazard Symbol13
Explosion Hazard Symbol13
— The Metal Of Conduit Is Not An Acceptable Ground —15
Grounding Capacitor Switch15
Dynamic Braking Precaution18
- Figure 1. Typical Circuit Breaker Configuration.21
Power Connections22
- Figure 2. Typical Q9 Plus ASD 3- phase input/output terminals and the Grounding Capacitor Switch.22
- Power Connection Requirements23
  - Figure 3. Q9 Plus ASD/Motor Typical Connection Diagram.23
System Grounding23
- Grounding Capacitor24
Terminal Descriptions27
- Figure 8. The relay is shown in the normal operating condition (default setting). During a faulted condition the relay connection is FLC-to-FLA.29
- Figure 9. Terminal Board.29
Terminal Board I/O Configurations30
- Figure 10. Discrete Input.30
- Figure 11. RR Input.30
- Figure 12. RX Input.30
- Figure 13. V/I Input.30
- Figure 14. P24 Output.30
- Figure 15. PP Output.30
- Figure 16. OUT1/OUT2 Output.30
- Figure 17. FP Output.30
- Figure 18. AM/FM Output.30
- Figure 19. Fault Relay (shown not faulted).30
Typical ASD Connection Diagram31
- Figure 20. The Q9 Plus Typical Connection Diagram.31
Start Up and Test32
- Figure 21. The Q9 Plus ASD Electronic Interface Features.34
LED/LCD Screens35
- LED Screen Display35
- LED Character/Font Information35
- LCD Screen Display35
- LCD Character/Font Information35
Using the LCD Screen36
- Primary Menus of the LCD Screen36
- Remote Mounting Hardware37
- Remote Mounting Installation Precautions37
- Remote Mounting Using the Mounting Kit37
  - Figure 25. Front Panel Removal/Front Panel Connector Assembly.38
  - Figure 26. Remote Mounting Dimensions (inches/millimeters).38
- Remote Mounting without the Mounting Kit39
  - Figure 27. EOI Remote Mounting Dimensions (inches/millimeters).39
Search For Default Setting Changes41
Command and Frequency Control Selections46
- Figure 28. Command- and Frequency-Control Source Relationship.46
Command Control47
Frequency Control47
- Figure 29. Q9 Plus ASD Root Menu Navigation.48
Frequency Command Mode48
- Frequency Setting48
EOI Command Mode48
Monitor Mode50
Program Mode Menu Navigation52
- Figure 30. Input the electrical specifications to the motor.75
- Figure 31. Input the specifications to the transducer.75
- Figure 32. Local mode verification.76
- Figure 33. Set the maximum threshold value.76
- Figure 34. Set the minimum threshold value.76
- Figure 35. Complete the virtual linear pump setup.77
- Figure 36. Select an Operating Mode.77
- Figure 37 . UP/Down Frequency Operation Control Timing Diagram.143
Linear acceleration and deceleration is the default pattern and is used on most applications.187
- Figure 38 . Using Acc/Dec Switching.189
- Viewing Trip Information283
- Trip Record at Monitor Screen283
- Trip History284
- Clearing a Trip284
Blank Page2
Blank Page305

Related product manuals

Preview: Toshiba Q9

Toshiba Q9 Series

Preview: Toshiba SuperMulti Drive

Toshiba SuperMulti Drive

Preview: Toshiba ACE-tronics G9 ASD

Toshiba ACE-tronics G9 ASD

Preview: Toshiba T300MV2

Toshiba T300MV2

Preview: Toshiba XM-6201B

Toshiba XM-6201B

Preview: Toshiba T300MVi

Toshiba T300MVi

Preview: Toshiba G9