Toshiba Super MMY-MAP0801HT8 - Data Display of Outdoor Cycle

208
3. Data display of outdoor cycle (Displayed on each outdoor unit)
4. Data display of outdoor cycle (Displayed on the header unit)
∗ This method is used when information of the follower unit is displayed on 7-segment display of the header unit.
SW01
1
SW02
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
SW03
2
Display contents
Pd pressure data Pd pressure (MPaG) is displayed with decimal data.
(MPaG: Approx. 1/10 value of kg/cm
2
G data)
Ps pressure data Ps pressure (MPaG) is displayed with decimal data.
PL pressure conversion data Estimated pressure of liquid line (MPaG) is displayed with decimal data.
TD1 sensor data Temperature sensor data (°C) is displayed
with decimal notation.
TD2 sensor data
• Symbol display for 1 sec. and data display for 3 sec. are
alternately displayed.
TS sensor data
• Data is displayed in [∗].
• Negative data is displayed as [– ∗ ∗ ∗ ∗].
TE sensor data
—
TL sensor data
TO sensor data
TK1 sensor data
TK2 sensor data
TK3 sensor data
TK4 sensor data
— A —
B —
— A —
B
AB
P d. ∗. ∗ ∗
P S. ∗. ∗ ∗
P L. ∗. ∗ ∗
Symbol t d 1 1 1
Data ∗∗ ∗. ∗
Symbol t d 2 1 1
Data ∗∗ ∗. ∗
Symbol t S
Data ∗∗ ∗. ∗
Symbol t E
Data ∗∗ ∗. ∗
Symbol ——
Data ——
Symbol t L
Data ∗∗ ∗. ∗
Symbol t o
Data ∗∗ ∗. ∗
Symbol F 1
Data ∗∗ ∗. ∗
Symbol F 2
Data ∗∗ ∗. ∗
Symbol F 3
Data ∗∗ ∗. ∗
Symbol F 4
Data ∗∗ ∗. ∗
SW01
3
SW02
1
2
3
4
5
6
7
SW03
1 to 3
Display contents
Error data A [U. ∗] ∗: SW03 setup number + 1 number (Outdoor unit number U2 to U4)
B Check code is displayed. (Latest check code only)
No check code: [– – –]
Installed compressor type A [U. ∗] ∗: SW03 setup number + 1 number (Outdoor unit number U2 to U4)
B
Outdoor unit capacity A [U. ∗] ∗: SW03 setup number + 1 number (Outdoor unit number U2 to U4)
B 8HP: [
… …
8]. 10HP: [
…
1 0], 5 to 12HP
Compressor operation command A [U. ∗] ∗: SW03 setup number + 1 number (Outdoor unit number U2 to U4)
B No.1 compressor ON: [C10], No.2 compressor ON: [C01]
For unconnected compressor, “ – ” is displayed.
Fan operation mode A [U. ∗] ∗: SW03 setup number + 1 number (Outdoor unit number U2 to U4)
B Stop time: [F
…
0], Mode 31: [F 3 1]
Release signal A [U. ∗] ∗: SW03 setup number + 1 number (Outdoor unit number U2 to U4)
B Normal time: [r
… …
], Release received: [r
…
1]
Oil level judgment A [U. ∗] ∗: SW03 setup number + 1 number (Outdoor unit number U2 to U4)
B Normal time: [
… … …
], Oil shortage: [
… …
L]
NOTE) The follower unit is setup by changing SW03.
SW03
7-segment display A
123
U2 U3 U4