Trane ProSpace PTHF User Manual

PTAC-SVX002A-EN
19
Table 4. Dip Switch Descriptions (continued)
Dip Switch Number Up Down Default Re-
marks
5/6: Setpoint Temperature Limits.
Provides a range of temperature control.
Up/Up
68°F to
75°F
(20°C to
24°C)
Up/
Down
63°F to
80°F
(18°C to
28°C)
Down/
Up
65°F to
78°F
(19°C to
26°C)
Down/
Down
61°F to
86°F
(16°C to
30°C)
Up/Up
61°F to
86°F
(16°C to
30°C)
Config.
5 and 6
combine
to select
set point
range.
When
setpoint
limit set,
display
always
shows
full
range.
7: Room Freeze Protection. If the unit
senses a room temperature below 40°F
(4.44°C), the fan motor and electric strip
heat turns ON and warms the room to 50°F
(10°C). The fan stops a short time after the
temperature is satisfied.
Freeze
Guard
Disable
Freeze
Guard
Enable
Down
Keypad Configuration
The Trane ProSpace can be customized by configuring the keypad.
1. To enter the keypad configuration screen, first power up the unit.
2. Within the 30 seconds after power-up press and hold both the ffaann ssppeeeedd ++
buttons for five
(5) seconds.
NNoottee:: If waiting more than 30 seconds after power-up, you cannot access the keypad
configuration. Power down and power up the unit again to restart the process.
3. To scroll through the available options, press and release the ffaann ssppeeeedd button to select the
keypad configurations. The stored value displays.
4. To exit the configuration screen, press the mmooddee button or after 30 seconds, the unit will
automatically exit the configuration screen.
5. To modify configuration settings, press and release simultaneously, either the SSeettppooiinntt ++
or
SSeettppooiinntt ++
buttons. Choose from the following four (4) options:
• FFaahhrreennhheeiitt//CCeellssiiuuss DDiissppllaayy SSwwiittcchh; changes between degrees Fahrenheit (F, default)
and Celsius (C) on the display.
• IInnddoooorr AAiirr TTeemmppeerraattuurree SSeennssoorr BBiiaassiinngg ffoorr CCoooolliinngg MMooddee; adjusts the room air
temperature reading when in cooling mode (not normally required).
• IInnddoooorr AAiirr TTeemmppeerraattuurree SSeennssoorr BBiiaassiinngg ffoorr HHeeaattiinngg MMooddee; adjusts the room air
temperature reading when in heating mode (not normally required).
• IInnddoooorr TTeemmppeerraattuurree DDiissppllaayy; changes between showing the setpoint or desired
temperature during heating and cooling modes (SP, default) or displaying the actual room
temperature during heating and cooling modes (AA).
– Selecting SP displays the desired setpoint temperature during heating and cooling
modes, regardless of what the actual temperature is in the room .
– Selecting AA displays the room temperature during heating, cooling, and fan-only
modes
– Changing the mode button to either heating or cooling modes displays the setpoint for
10 seconds. After the 10 seconds, the room temperature displays.
– Depressing the ON-OFF when the unit is OFF, and the last mode was either cooling or
heating, the setpoint displays for 10 seconds before displaying the room temperature.
– Depressing either
or during heating and cooling mode displays the setpoint for 10
SSyysstteemm CCoonnffiigguurraattiioonn

Trane ProSpace PTHF Specifications

General

Brand	Trane
Model	ProSpace PTHF
Category	Air Conditioner
Language	English