EasyManua.ls Logo

Triton T70 GSI - User Manual

Triton T70 GSI
28 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
2181056I - November 2020
T70 GSI
electric shower
INSTALLATION AND OPERATING INSTRUCTIONS
Please read this book thoroughly and familiarise yourself with all instructions before commencing
installation and keep it for future reference.
The shower installation MUST be carried out by a suitably qualified person, in the sequence of
this instruction book.
IMPORTANT SAFETY ADVICE
The shower unit MUST BE switched off at the
isolating switch when not in use. This is a
safety procedure recommended for all
electrical appliances.
The showerhead and hose supplied with this
product are a safety critical part of your shower.
Failure to use genuine Triton parts may cause
injury and invalidate your guarantee.
FOR YOUR SERVICE REFERENCE
NOTE DOWN THE PRODUCT CODE BELOW
(FROM THE FRONT OR TOP OF THE BOX)
ALTERNATIVELY REGISTER BY TEL: 024 7637 8321
THIS OFFER IS NOT VALID OUTSIDE THE UK
REGISTER ONLINE
ENTER A PRIZE DRAW
WIN
£100
LOVE2SHOP VOUCHERS
VISIT OUR WEBSITE TODAY
TRITONSHOWERS.CO.UK/REGISTER
PRODUCT REGISTRATION IS ONLY AVAILABLE
TO UNITS PURCHASED & INSTALLED IN THE UK

Table of Contents

Questions and Answers

  • B
    buchananterriAug 8, 2025
    Why is my Triton Bathroom Fixture shower not working?
    • U
      ularsenAug 8, 2025
      Your Triton Bathroom Fixture shower might not be working due to several reasons: * There could be an interrupted power supply, such as a blown fuse or circuit breaker. In this case, check and renew or reset the fuse or circuit breaker. If it fails again, consult a qualified electrician. * There might be a power cut. Check other appliances and, if necessary, contact your local Electricity Supply Company. * There might be no mains water supply to the shower. Ensure that isolating valves are fully open and check for a blockage in the inlet filter or pipework. * The unit might have malfunctioned. It is recommended to have the unit checked.
  • A
    Ann WrightAug 12, 2025
    What to do if my Triton Bathroom Fixture shower is too hot?
    • D
      Derrick ClarkAug 12, 2025
      If your Triton Bathroom Fixture shower water is too hot, it could be due to: * Not enough water flowing through the shower. Try increasing the flow rate via the temperature control. * A blocked showerhead. Clean or replace the blocked sprayplate in the showerhead. * A blockage in the supply. Check if the stop valves are fully open and inspect the inlet filter for blockages. * An increase in ambient water temperature. Readjust the flow rate to increase the water flow or select economy power.
  • A
    Amber VincentAug 16, 2025
    What to do if my Triton Bathroom Fixture shower pressure relief device is ejecting water?
    • S
      Sierra FloresAug 17, 2025
      If the pressure relief device (PRD) in your Triton Bathroom Fixture is ejecting water, it could be due to: * A blocked showerhead. Clean or replace the blocked sprayplate and then fit a new PRD. * A twisted or blocked flexible shower hose. Check for free passage through the hose and replace it if necessary, then fit a new PRD. * The showerhead not being removed during commissioning. Fit a new PRD and commission the unit with the showerhead removed. * Water pressure being above the specified maximum. Fit a pressure reducing valve to the inlet and then fit a new PRD.
  • J
    Jennifer Bennett MDAug 21, 2025
    Why is my Triton Bathroom Fixture shower water temperature cycling hot and cool?
    • J
      Jennifer HolmesAug 21, 2025
      If the water temperature in your Triton Bathroom Fixture shower is cycling between hot and cool, it might be due to the heater cycling on thermal cut-out. Refer to the causes for ‘Water too hot’ related to flow and blockages and take appropriate action. If the issue continues, it is recommended to contact Customer Experience.
  • P
    paulamcdanielAug 26, 2025
    What to do if my Triton Bathroom Fixture shower is too cool or cold?
    • J
      James HansenAug 26, 2025
      If your Triton Bathroom Fixture shower is too cool or cold, consider the following: * There might be too much flow. Reduce the flow rate via the temperature control. * The water pressure might be below the minimum required. Determine if the water supply is mains or tank fed. If tank fed, replumb to the mains water supply. If mains fed, ensure the stop valve is fully open and there are no other supply restrictions while the shower is in use. You can also fit a pump to achieve the minimum pressure. * There might be a reduction in ambient water temperature. Readjust the flow rate to reduce the water flow or select ‘high’ power. * There could be an electrical malfunction or the safety cut-out has operated. Have the unit checked by a qualified electrician.
  • N
    Nicholas MartinAug 29, 2025
    What to do if my Triton Bathroom Fixture shower varies from normal temperature to cold?
    • J
      jenniferparkerAug 30, 2025
      If your Triton Bathroom Fixture shower's temperature varies from normal to cold during use, it's likely that the water pressure has dropped below the required minimum. Wait until the water pressure returns to normal.
  • L
    Lisa OliverSep 3, 2025
    What to do if my Triton Bathroom Fixture shower fails to shut off?
    • N
      Natalie MooreSep 3, 2025
      If your Triton Bathroom Fixture shower fails to shut off, it could be due to: * A faulty start/stop microswitch. Replace the microswitch. * Debris in the solenoid valve. Replace the solenoid valve. * Unit malfunction. It is recommended to have the unit checked.

Triton T70 GSI Specifications

General IconGeneral
TypeElectric Shower
Showerhead Settings5 Spray Patterns
MaterialPlastic
Number of Spray Modes5
Maximum Pressure10 bar
Warranty2 Years
Power Rating10.5 kW
InstallationWall-mounted
Water Entry PointsTop, Bottom
Cable Entry PointsTop, Bottom
FeaturesLow Pressure Indicator, Phased Shutdown
FinishWhite

Related product manuals