True TC650 - User Manual

Questions and Answers

A
Adam SalazarSep 23, 2025
How to fix Fault SP03 Belt Over Accel on True TC650 Treadmill?
- F
  fordmelissaSep 23, 2025
  If your True Treadmill displays 'Fault SP03: Belt Over Accel', avoid trying to stop the belt manually and lubricate the treadbelt.
A
Ashley BoydSep 23, 2025
What to do if my True TC650 shows Fault SP02 Belt Over Speed?
- S
  Samuel MatthewsSep 23, 2025
  If your True Treadmill displays 'Fault SP02: Belt Over Speed', lubricate the treadbelt and check the AC line voltage.
Q
qrichardsonAug 31, 2025
What should I do if my True TC650 displays Fault A109?
- K
  Kristin MayerAug 31, 2025
  If your True Treadmill displays Fault A109, which indicates a motor controller fault, power cycle the treadmill and check cable connections.
S
Steven PhillipsAug 25, 2025
What to do if my True TC650 resets randomly?
- M
  millercatherineAug 25, 2025
  If your True Treadmill resets or pauses randomly, check the following: - Replace the power cord if damaged. - Ensure the power cord is fully seated in the socket at both the unit and the outlet. - Make sure the safety e-stop key is fully engaged with the console. - Use a voltmeter to verify the output voltage from the 20A outlet to ensure sufficient power. If an error code is displayed on the console, further assistance is needed.
A
Amy McleanAug 25, 2025
How to troubleshoot a True TC650 with no power?
- C
  Christopher MejiaAug 26, 2025
  First, verify that the On/Off switch is in the ON position. Then, inspect the power connection at both the unit and the outlet to ensure the power cord is fully seated. Check the circuit breaker next to the On/Off switch to make sure it hasn't tripped; if it has, reset it. Use a voltmeter to verify that there is power at the outlet. Finally, examine the power cord for any damage and replace it if necessary.
S
Stephen TaylorAug 26, 2025
Why is the heart rate displaying erratically on my True TC650 Treadmill?
- N
  Nancy PearsonAug 26, 2025
  Make sure the transmitter belt contacts are making good contact with your skin and are moist. Ensure the transmitter belt is within 3 feet (1 meter) of the heart rate receiver on the console. If you are still experiencing issues, replace the transmitter belt, as the battery inside may be depleted. Also, environmental interference from high voltage power lines may cause this issue, try moving the unit to another position within the room or move the cause of the interference until heart rate reading are stable. If the probable source of interference is plugged into the same outlet move the suspect source to another outlet. Finally, another user wearing a compatible transmitter strap may be interfering, so move the units further apart.
C
Christopher AdkinsAug 26, 2025
How to fix a True TC650 walking belt that is off center?
- H
  Hayley ScottAug 26, 2025
  If the walking belt is off center, start by adjusting the rear leveling feet to compensate for an uneven floor. Also, you can adjust the belt alignment.
S
Suzanne MayAug 27, 2025
What to do if the walking belt hesitates or slips when stepping on my True TC650 Treadmill?
- H
  Hector VaughnAug 27, 2025
  If the walking belt hesitates or slips, you may need to adjust the belt tension. Also, you can adjust the belt alignment.
I
Isaac PalmerAug 27, 2025
Why does my True TC650 Treadmill make a rubbing sound when I use it?
- N
  Nathan MoodyAug 27, 2025
  A rubbing sound during operation could be due to a foreign object stuck under the walking belt. Inspect under the unit and remove any object that may be there.
M
Maria BairdAug 27, 2025
What does Fault CN09 mean on my True TC650 Treadmill?
- T
  Terry GarciaAug 27, 2025
  Fault CN09 indicates that the safety key is not engaged. Re-insert the safety key. Also, check cable connections.